Due to the good neutronics,thermal hydraulics and safety characteristics of lead-based coolants,Lead-based Nuclear Energy Systems（LNESs）have generated great interest in the research field of international advanced nuclear energy systems,including the lead and lead-bismuth cooled fission reactors and the Lithium Lead（LiPb）cooled fusion reactors.Based on the high boiling point characteristics of the lead-based coolant,the core outlet temperature of the LNESs can reach above 500℃.Therefore,the LNES... 

【文章來源】：中國科學技術大學安徽省 211工程院校 985工程院校

【文章頁數】：136 頁

【學位級別】：博士

【文章目錄】：
Abstract
Nomenclature and Acronyms
Preface
Chapter 1 Introduction
    1.1 Principle and Characteristics of Lead-based Nuclear Energy Systems
        1.1.1 Characteristics of LFR
        1.1.2 Characteristics of Fusion Reactor Blankets
    1.2 Overview of Lead-based Nuclear Energy Systems
        1.2.1 Worldwide Status of LFR
        1.2.2 Worldwide Status of Fusion Reactor Blankets
        1.2.3 Characteristics of Fusion Reactor Blankets
    1.3 Overview of Power Generation System for LNESs
        1.3.1 Overview of Power Generation System for LFR
        1.3.2 Overview of Power Generation System for DLL Blanket
    1.4 Technical Challenges and Research Objectives
    1.5 Outline of Dissertation
Chapter 2 Design Models and Methods
    2.1 Basic Principal
        2.1.1 Assumptions in Analysis of LFR Power Generation System
        2.1.2 Assumptions in Analysis of DLL Blanket of Power Generation System
    2.2 Thermodynamic Model Based on Rankine Cycle
        2.2.1 Heat Balance for Steam Generator
        2.2.2 Mass Flow Rate across Each Section
        2.2.3 Power Produced by Turbine
        2.2.4 Condenser and Feed Water Heater Power
        2.2.5 Heat Removed by Condenser
        2.2.6 Energy Balance for Feed Water Heater and Deaerator
        2.2.7 Heat Rate of Plant
        2.2.8 Total Power of Plant
        2.2.9 Thermal Efficiency of Plant
    2.3 Design Calculation for Steam Generator
        2.3.1 Mathematical Method
        2.3.2 Numerical Model
    2.4 Thermodynamic Model Based on Brayton Cycle
        2.4.1 Thermodynamic Extraction of Heat from Blanket to Brayton Cycle
        2.4.2 Power Produced by HP and LP Turbines
        2.4.3 Power Required to Compressors Ⅰ and Ⅱ
        2.4.4 Heat Extracted by Intercooler
        2.4.5 Recuperator
    2.5 Summary
Chapter 3 Conceptual Design of Power Generation System for LFR
    3.1 Design of Power Generation System
        3.1.1 Main Parameters of LFR
        3.1.2 Schematic of Power Generation System
        3.1.3 Mathematical Calculation
        3.1.4 Design Modification of Power Generation System
    3.2 Effect of Main Inlet Parameters
        3.2.1 Effect of Feed Water Temperature
        3.2.2 Effect of Steam Outlet Temperature
        3.2.3 Effect of Mass Flow Rate
    3.3 Performance Optimization of Power Generation System
        3.3.1 Description of Schematic-Ⅲ
        3.3.2 Optimization of Turbine Pressure
        3.3.3 Optimization of Condenser Back Pressure
    3.4 Part Load and Secondary Loop Performance
    3.5 Heat Rate of Plant
    3.6 Summary
Chapter 4 Analysis of Steam Generator for LFR
    4.1 Main Design Parameters of Steam Generator
        4.1.1 Design Parameters of Steam Generator
        4.1.2 Structural Material for Steam Generator
    4.2 Sizing of Steam Generator
        4.2.1 Bayonet Tube Steam Generator
        4.2.2 Design Description of Bayonet Tube Steam Generator
    4.3 Thermal Analysis on Steam Generator Performance
        4.3.1 Effect of Steam Generator Inlet Temperature on Thermal performance
        4.3.2 Effect of Inlet Temperature on Power Generation
        4.3.3 Analysis on Steam Generator Mass Flow Rate verses Power Generation
        4.3.4 Evaluation of Steam Generator Mass Flow Rate Verses Partial Load
    4.4 Summary
Chapter 5 Design of Power Generation System for DLL Blanket of FDS-II
    5.1 Design Description of Power Generation System
    5.2 Design Calculations
        5.2.1 Thermodynamic Extraction of Heat from Blanket to Brayton Cycle
        5.2.2 Power Produced by High and Low Pressure Turbines
        5.2.3 Power Required to Compressors Ⅰ and Ⅱ
        5.2.4 Heat Extracted by Intercooler
        5.2.5 Recuperator
        5.2.6 Performance Evaluation
    5.3 Optimization of Parameters and Performance Evaluation
        5.3.1 Pressure Ratio and Isentropic Efficiency
        5.3.2 Recuperator Analysis and Inlet Temperature of DLL Blanket
        5.3.3 Back Work Ratio of System
        5.3.4 Effect of Pressure
    5.4 Summary
Chapter 6 Design of Intermediate Heat Exchanger for DLL Blanket
    6.1 Concept Design of CHE
    6.2 Numerical Model and Boundary Conditions
        6.2.1 Thermal Boundary Conditions and Properties of Working Fluids
        6.2.2 Mesh Model Validation
    6.3 Thermal Performance Assessment
        6.3.1 Structure Material Evaluation
        6.3.2 Heat Transfer Performance of Structures
        6.3.3 Nusselt Number
        6.3.4 Pressure Drop
    6.4 Summary
Chapter 7 Conclusions, Implications and Future Work
    7.1 Conclusions
    7.2 Innovation
    7.3 Implications and Future Work
References
List of Publications
Achievements
Project List
Acknowledgements


【參考文獻】：
期刊論文
[1]Tumor Molecular Imaging with Nanoparticles[J]. Zhen Cheng,Xuefeng Yan,Xilin Sun,Baozhong Shen,Sanjiv Sam Gambhir.  Engineering. 2016(01)
[2]鉛基反應堆研究現狀與發展前景[J]. 吳宜燦,王明煌,黃群英,趙柱民,胡麗琴,宋勇,蔣潔瓊,李春京,龍鵬程,柏云清,劉超,周濤,金鳴,FDS團隊.  核科學與工程. 2015(02)
[3]中國鉛基研究反應堆概念設計研究[J]. 吳宜燦,柏云清,宋勇,黃群英,劉超,王明煌,周濤,金鳴,吳慶生,汪建業,蔣潔瓊,胡麗琴,李春京,高勝,李亞洲,龍鵬程,趙柱民,郁杰,FDS團隊.  核科學與工程. 2014(02)
[4]高溫氣冷堆氦氣透平循環熱工特性的初步研究[J]. 王捷.  高技術通訊. 2002(09)



本文編號：3192496