【摘要】：以3-吲哚乙酸(IAA)為模板分子、丙烯酰胺(AA)為功能單體,采用沉淀聚合法制備了IAA印跡聚合物微粒,研究了致孔劑乙腈的用量及IAA的加入量對印跡聚合物結合性能的影響,采用色譜法對其進行評價。結果表明,當乙腈為37.5 m L,IAA為2 mmol(與AA物質的量比為1∶1)時,制得印跡聚合物P7對IAA的親和力最大(k=4.24),印跡因子(IF)為14.1,其對IAA展示了最顯著的特異識別能力。將P7作為固相萃取柱的填料,研究了分子印跡固相萃取IAA的方法,測得綠豆芽樣品的加標回收率為90.6%~92.6%。結果表明,以AA為功能單體沉淀聚合法制備的IAA印跡聚合物顆粒適合作為固相萃取柱填料,可實現實際樣品中IAA的選擇性分離凈化。該文提出的采用適當增大模板分子加入量的方法是制備高親和力與高選擇性印跡聚合物的一條新途徑。
[Abstract]:IAA imprinted polymer particles were prepared by precipitation polymerization with 3-indoleacetic acid (IAA) as template molecule and acrylamide (AA) as functional monomer. The effects of the amount of acetonitrile and the amount of IAA on the binding properties of imprinted polymers were studied. The results showed that when acetonitrile was 37.5 mL, IAA was 2 mmol (the ratio to AA was 1:1), the imprinted polymer P7 had the highest affinity to IAA (KN 4.24), and the imprinting factor (IF) was 14.1. It shows the most remarkable recognition ability for IAA. Using P7 as the filler of solid-phase extraction column, the method of molecularly imprinted solid-phase extraction (IAA) was studied. The standard recovery of mung bean sprouts was 90.6% ~ 92.6%. The results showed that the IAA imprinted polymer particles prepared by precipitation polymerization of AA as functional monomers were suitable for solid phase extraction column packing and could realize the selective separation and purification of IAA in practical samples. It is a new way to prepare high affinity and high selectivity imprinted polymers by increasing the amount of template molecule.
【作者單位】： 唐山師范學院化學系;河北科技大學生物科學與工程學院;
【基金】：唐山師范學院團隊支撐重點項目(2014D07)
【分類號】：O631.3;O658.2

【相似文獻】

相關期刊論文 前10條

1 劉崢;溫玉清;黃美春;;銅離子印跡聚合物的制備及吸附性能[J];桂林工學院學報;2007年01期

2 王玲玲;閆永勝;鄧月華;李春香;徐婉珍;;鉛離子印跡聚合物的制備、表征及其在水溶液中的吸附行為研究[J];分析化學;2009年04期

3 賴曉綺;楊遠奇;薛s，

本文編號：2344859