發布時間：2018-07-04 22:45

  本文選題：運動控制系統 + 工業以太網　； 參考：《廣東工業大學》2017年碩士論文

【摘要】：運動控制系統是數控裝備實現精密加工的關鍵設備。隨著工業自動化技術的不斷發展,網絡化、智能化和柔性化的運動控制系統成為未來的發展趨勢。傳統的基于現場總線技術的運動控制系統已不能滿足需求,工業以太網以其實時性強、通信容量大、開放性好等優點逐步被廣泛應用于運動控制系統當中。EtherCAT工業以太網因其通信速度快、可靠性高以及同步性好而備受青睞。本文將EtherCAT實時工業以太網技術引入多軸運動控制系統當中,在深入研究多軸運動控制技術和EtherCAT網絡技術的基礎上,進行了從站運動控制器軟硬件開發,設計了EtherCAT主站數控軟件。運動控制系統在通過一系列測試后,成功應用在數控轉塔沖床上。論文主要研究內容和成果如下:1.研究了運動控制系統在國內外的發展現狀,在比較了主流的實時工業以太網后,采用EtherCAT以太網來實現控制系統內部的通信。對EtherCAT協議進行了深入研究,提出了運動控制系統總體的設計方案,又分別設計了控制系統硬件和軟件方案。2.選用無風扇的工業PC機作為控制主站,詳細設計了從站運動控制器的EtherCAT通信電路、ARM控制電路、伺服接口電路以及電源電路,在完成PCB板的布局布線后成功開發出控制器樣機。3.在主站PC機軟件部分,改造了linux實時性、安裝了EtherCAT主站和Linux CNC、編寫了數控界面。從站運動控制器軟件部分完成了ARM主控制程序、ET1200通信程序、FSMC總線驅動以及加減速控制算法。實現了從G代碼文件輸入到控制軸精確定位的整套軟件。4.在控制系統軟硬件設計完成后,搭建了實驗平臺,進行了主從站之間的通信測試、控制系統的基本功能測試、G代碼解釋功能測試、圓弧插補功能測試以及多軸同步功能測試,在通過一系列實驗測試后在LX230B型數控沖床上進行了高速點動實驗,實現了預期的運動控制效果。運動控制系統總體測試結果達到設計要求,為進一步研究奠定了良好的基礎。
[Abstract]:Motion control system is the key equipment for NC equipment to realize precision machining. With the development of industrial automation technology, networked, intelligent and flexible motion control system will become a trend in the future. The traditional motion control system based on fieldbus technology can not meet the needs of industrial Ethernet because of its strong real-time, large communication capacity, The advantages of good openness have been widely used in motion control systems. EtherCAT industrial Ethernet has been favored for its high communication speed, high reliability and good synchronization. In this paper, EtherCAT real-time industrial Ethernet technology is introduced into multi-axis motion control system. On the basis of deep research on multi-axis motion control technology and Ethernet network technology, hardware and software of slave station motion controller are developed, and EtherCAT master station numerical control software is designed. The motion control system is successfully applied to CNC turret punch after a series of tests. The main research contents and results are as follows: 1. The development of motion control system at home and abroad is studied. After comparing the mainstream real-time industrial Ethernet, EtherCAT Ethernet is used to realize the internal communication of the control system. In this paper, the EtherCAT protocol is deeply studied, and the overall design scheme of the motion control system is put forward, and the hardware and software schemes of the control system are designed respectively. The industrial PC without fan is selected as the main control station. The EtherCAT communication circuit, servo interface circuit and power supply circuit of the slave station motion controller are designed in detail. After the PCB layout and wiring is completed, the controller prototype .3is developed successfully. In the part of PC software of the master station, the real-time performance of linux is reformed, the EtherCAT master station and linux CNC are installed, and the NC interface is written. From the software of the station motion controller, the arm main control program, ET1200 communication program and FSMC bus drive and acceleration and deceleration control algorithm are completed. Realized from G code file input to the control axis accurate positioning software. 4. After the hardware and software design of the control system is finished, the experimental platform is built, the communication test between the master and slave stations, the basic function test of the control system, the code interpretation function test of the control system, the arc interpolation function test and the multi-axis synchronization function test are carried out. After a series of experimental tests, a high speed spot motion experiment was carried out on the LX230B CNC punch, and the desired motion control effect was achieved. The overall test results of the motion control system meet the design requirements and lay a good foundation for further research.
【學位授予單位】：廣東工業大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TP273

【參考文獻】

相關期刊論文 前8條

1 陳啟雷;張禮兵;陳俊澍;胡樂意;;運動控制器的應用現狀及其發展趨勢[J];科技創新與應用;2017年05期

2 魏亞鵬;韓衛光;;實時工業以太網技術的研究[J];組合機床與自動化加工技術;2013年07期

3 韓軍;常瑞麗;;基于單片機的脈沖式運動控制器的開發與研究[J];機械設計與制造;2011年08期

4 汪毅強;楊娟;趙大勝;;ARM與FPGA通信接口板設計[J];硅谷;2011年09期

5 康存鋒;林志磊;馬春敏;黃旭東;費仁元;;基于TwinCAT主站的EtherCAT實時以太網分析與研究[J];現代制造工程;2010年11期

6 馮世寧;馬杰;趙雪飛;;若干種實時以太網標準的比較[J];南京師范大學學報(工程技術版);2010年02期

7 蔣仕龍;吳宏;呂恕;龔小云;;通用運動控制技術現狀、發展及其應用[J];電工文摘;2009年01期

8 吳麗珍;郝曉弘;;工業以太網絡控制系統的建模及其控制器設計[J];蘭州理工大學學報;2008年04期

，

本文編號：2097764