【摘要】：隨著無線通信技術的發展,其應用也越來越廣泛,除民用外也逐漸涉及國防軍事等領域,所以天線系統對功率有了更高的要求。短波通信的過程中,經常需要采用一定的反干擾手段來保證通信質量,最常用的是空間功率合成技術,高精度的相位差則是其中的重要指標。本文針對天線陣信號,對移相信號進行高精度檢測并進行信號質量分析,主要完成工作有:1.針對采用主流相位檢測方法的缺陷,對網絡化天線陣列系統中移相特性及相位檢測技術進行深入的研究分析與驗證,采用荷蘭TiePie HS5-530數據采集計算與AD8302硬件相位差檢測電路相結合的方式實現系統功能。相位差硬件檢測電路將相位差信息轉換為電平信息,然后通過串口通信將結果傳送到上位機,最后上位機將采樣數據處理結果與硬件檢測結果統一進行曲線擬合處理得出所需相位差結果。2.實現硬件平臺搭建,主要工作包括工控機的定制與內部各功能模塊的連接布局、數據采樣模塊的特點及開發需求、硬件相位差檢測電路,確定硬件系統的整體框架,最終完成對硬件系統的整體設計。3.在數據處理的過程中系統主要完成對天線射頻信號的采樣與分析處理,包括FFT、波形還原、頻譜分析、相位差檢測、結果顯示等功能;實現移相特性采樣分析的自動化,同時得到多路信號間相位差的高精度結果(±1°)。另外在程序的結果顯示界面,本文實現了信號波形還原和頻譜顯示功能。同時對信號質量分析結果顯示在相應區域,包括信號頻率、幅度、駐波比和信號間的相位差等;另外還有信息提示區實時反映系統的運行狀態。在實現上述功能的前提下,擴展了遠程控制功能;用戶可以在遠端通過IE登錄控制系統的功能實現,并將結果數據通過TCP/IP通信協議接收并存儲。4.在整個系統設計完成后,根據項目指標要求,通過一系列例行試驗對系統整體進行測試,將各組試驗數據結果進行精度分析,結果表明在初步測試的過程中本系統在各種模擬惡劣環境中都能夠滿足指標要求。最后對本系統的遠程通信功能進行驗證測試,在IE端能夠通過網絡化天線控制平臺遠程操控程序的執行,可知本系統的網絡化功能也能夠滿足要求。但是,本文所設計的系統也存在不足之處。首先數據庫系統設計不夠完善,對數據的存儲管理功能有待提高;另外程序執行界面視覺效果也需要進一步美化。
[Abstract]:With the development of wireless communication technology, its application is more and more extensive. Besides civil affairs, it is also gradually involved in the field of national defense and military affairs, so the antenna system has higher requirements for power. In the process of shortwave communication, some anti-interference means are often used to ensure the communication quality. The most commonly used technology is the space power synthesis technology, and the high precision phase difference is one of the important indexes. In this paper, the phase shift signal is detected with high precision and the signal quality is analyzed. The main work is as follows: 1. Aiming at the defects of the mainstream phase detection method, the phase shift characteristics and phase detection techniques in networked antenna array systems are studied and verified. The system functions are realized by combining Dutch TiePie HS5-530 data acquisition and AD8302 hardware phase difference detection circuit. The phase difference information is converted into the level information by the hardware detecting circuit of phase difference, and the result is transmitted to the upper computer through serial communication. Finally, the data processing result of sampling and the result of hardware testing are unified by the upper computer to get the desired phase difference result by curve fitting. 2. The main work includes the customization of the industrial computer and the connection layout of the internal functional modules, the characteristics and development requirements of the data sampling module, the hardware phase difference detection circuit, and the overall frame of the hardware system. The final completion of the hardware system of the overall design. 3. In the process of data processing, the system mainly completes the sampling and processing of antenna RF signals, including the functions of FFT, waveform reduction, spectrum analysis, phase difference detection, result display, etc. At the same time, the high accuracy results of phase difference between multichannel signals are obtained (鹵1 擄). In addition, in the result display interface of the program, this paper realizes the function of signal waveform restoration and spectrum display. At the same time, the results of signal quality analysis are shown in the corresponding regions, including signal frequency, amplitude, standing wave ratio and phase difference between signals, and there are also information warning areas to reflect the running state of the system in real time. On the premise of realizing the above functions, the remote control function is extended, the user can realize the function of the remote access control system through IE, and the result data is received and stored through the TCP/IP communication protocol. 4. After the design of the whole system is finished, according to the requirements of the project index, the whole system is tested through a series of routine tests, and the accuracy of the results of each group of test data is analyzed. The results show that the system can meet the requirements in various simulation environments. Finally, the remote communication function of the system is verified and tested. The remote control program of the platform can be controlled by the network antenna in the IE terminal, and the network function of the system can also meet the requirements. However, the system designed in this paper also has shortcomings. First, the design of database system is not perfect, and the function of data storage and management needs to be improved. In addition, the visual effect of program execution interface also needs to be further beautified.
【學位授予單位】：西安電子科技大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TN828

【相似文獻】

相關期刊論文 前10條

1 宋長寶,竺小松;一種新型相位差測量系統[J];電子產品世界;2003年11期

2 張鵬,徐進,曹建榮;一種基于數字分析的相位差測量方法[J];計算機測量與控制;2004年03期

3 宋長寶;李志剛;竺小松;;基于數字正交變換的相位差測量方法及誤差分析[J];電路與系統學報;2006年01期

4 李國朝;黃慶華;;基于相關原理的相位差測量及虛擬相位差計的設計[J];微計算機信息;2007年01期

5 白澤生;;一種工頻相位差測量儀的設計[J];微計算機信息;2007年10期

6 易立強;鄺繼順;歐陽雄;;基于一類新窗的高精度相位差測量方法[J];系統仿真學報;2007年23期

7 朱偉強;黃培康;馬琴;;基于相位差變化率測量的單站定位方法[J];系統工程與電子技術;2008年11期

8 毛勇;江傳華;;利用相關分析實現低信噪比信號的相位差測量[J];艦船電子工程;2009年12期

9 劉龍飛;王根嶺;肖培如;;相位差測量電路的設計[J];工業控制計算機;2013年06期

10 梁志圖;張浩;嚴潔;;一種新穎多路相位差微機快速檢測方法[J];西安建筑科技大學學報(自然科學版);1986年01期

相關會議論文 前3條

1 翟瑞永;蕭寶瑾;;一種高頻信號相位差測量的方法[A];2007北京地區高校研究生學術交流會通信與信息技術會議論文集（上冊）[C];2008年

2 張忠紅;江海清;高梅國;;基于數字信道化接收機的相位差測量方法研究[A];第六屆全國信號和智能信息處理與應用學術會議論文集[C];2012年

3 廖家平;張友獎;姚銘;;一種高精度相位差測量系統的設計[A];湖北省電工技術學會、武漢電工技術學會2008年學術年會暨理事會換屆大會論文集[C];2008年

相關博士學位論文 前3條

1 李智奇;時頻信號的相位比對與處理技術[D];西安電子科技大學;2012年

2 周俊儒;基于RFID的室內定位技術研究[D];浙江大學;2014年

3 邢浩江;電網同步采集相位精度影響因素的權重分布與補償研究[D];哈爾濱工業大學;2010年

相關碩士學位論文 前10條

1 蔡卓淮;基于FPGA的科氏質量流量計相位差算法研究與實現[D];廣西大學;2015年

2 康旭;基于邊沿效應的高精度相位差測量技術[D];西安電子科技大學;2014年

3 楊鑫;短波通信天線系統移相特性及相位檢測技術的研究[D];西安電子科技大學;2014年

4 王蓮蓮;高精度數字式相位差測量系統的研究[D];蘇州大學;2006年

5 饒曉紅;高精度相位差測量系統的研究[D];電子科技大學;2010年

6 王超;高精度相位差檢測系統設計[D];西安電子科技大學;2012年

7 賈立鋒;高精度時頻信號的相位差及群相位差處理與測量技術研究[D];西安電子科技大學;2012年

8 于光運;高分辨率的距離變化——相位差精密測量技術[D];西安電子科技大學;2010年

9 楊明玲;相位差可調的正弦波信號發生器設計[D];哈爾濱理工大學;2014年

10 汪洋;用于絕對距離干涉測量的FPGA比相技術研究[D];西安理工大學;2009年

，

本文編號：2281348