發布時間：2018-11-05 18:45

【摘要】：在越發重視生態保護的今天,水輪機過魚時減少和消除對魚類損傷的能力已成為是否環境友好的重要指標�；趪�(guó)內某電站軸流式水輪機的設計參數建立模型,并基于魚類友好理念初步針對魚類普遍受傷因素對原始模型進行幾何形狀改進。運用CFD數值模擬方法,在同一工況下分別將模型的導葉、輪轂、輪緣、轉輪室進出口進行單一改型以及將整合所有改型方式后的模型與原始模型進行水力性能對比,得出導葉改型后效率降低1.76%,出力提升0.02k W;輪轂和轉輪室進出口改型后效率和出力基本不變;而輪緣改型后效率提升2.18%且出力增加0.07 k W;整合改型后的模型效率下降3.11%,出力降低0.05 k W。
[Abstract]:Nowadays, more and more attention has been paid to ecological protection, and the ability of hydraulic turbines to reduce and eliminate damage to fish has become an important indicator of environmental friendliness. Based on the design parameters of axial-flow turbine in a power station in China, the model was established, and the geometric shape of the original model was improved based on the concept of fish friendliness. Using CFD numerical simulation method, the guide vane, hub, wheel rim and runner chamber inlet and outlet of the model are single modified under the same working condition, and the hydraulic performance of the model after integrating all the modified modes is compared with the original model. The results show that the efficiency of the guide vane is reduced by 1.76 and the output of the guide vane is increased by 0.02 kW; The efficiency and output force of wheel hub and runner chamber were basically unchanged, while the efficiency and output force of wheel rim were increased by 2.18% and 0.07 kW, while the model efficiency and output force were decreased by 3.11 and 0.05 kW respectively.
【作者單位】： 河海大學能源與電氣學院;
【基金】：國家自然科學基金項目(51339005)
【分類號】：TV734.1

【相似文獻】

相關期刊論文 前10條

1 王正偉,崔濤,江德春,呂孟東;軸流式水輪機流道內部流動分析[J];大電機技術;2003年06期

2 張樂福;劉勝柱;羅興;張亮;;軸流式水輪機輪緣間隙三維紊流數值模擬[J];大電機技術;2009年02期

3 韓秀麗;劉萬江;張樂福;;軸流式水輪機間隙流動分析[J];大電機技術;2009年03期

4 陳泉開;;調槳技術在小微型軸流式水輪機上的應用[J];新技術新工藝;2009年06期

5 陳泉開;;小微型軸流式水輪機改進設計[J];福建工程學院學報;2009年04期

6 趙永智;;萬安電站~#5軸流式水輪機的水力開發[J];東方電機;2005年02期

7 任巖;王瑞蓮;陳德新;張小寶;;黃河水流對軸流式水輪機磨蝕及其防護研究[J];黃河水利職業技術學院學報;2007年01期

8 程良駿;對《330工程五葉片軸流式水輪機水力試驗的一些結果》的分析[J];華中工學院學報;1980年03期

9 崔維志;我省軸流式水輪機抗磨蝕試驗簡介[J];陜西水力發電;1986年02期

10 郭鵬程,羅興，

本文編號：2313023