【摘要】：為了探索薄煤層刨煤機刨刀刨削煤巖的破碎過程及其力學特性,基于有限元數值仿真分析方法分析煤巖截割過程的顯示動力特性。依據煤巖三向應力測試試驗,構建出基于Drucker Prager準則的煤巖本構模型。以煤巖刨削截深、煤巖刨削速度、刨刀前角為水平因素設計單因素仿真分析試驗,實現煤巖破碎形態與刨刀煤巖截割力的研究。研究結果表明:煤屑塊度與煤巖刨削截深有關,隨著截深的增大,塊度增大;隨著刨削速度的增加,煤屑的塊度變化趨勢不明顯,煤巖在α=30°刨刀作用下,截割剝離煤屑塊度較大;刨刀煤巖截割負載隨著截深的增大而增大;隨著轉速與截割深度的增加,前角為30°的刨刀負載呈線性上升趨勢。
[Abstract]:In order to explore the crushing process and mechanical characteristics of coal and rock in thin coal planer, the dynamic characteristics of coal and rock cutting are analyzed based on finite element numerical simulation method. Based on the three dimensional stress test of coal and rock, the constitutive model of coal and rock is constructed based on Drucker Prager criterion. The single factor simulation analysis test is designed with the horizontal factors of coal and rock cutting depth, coal and rock cutting speed and planer angle as horizontal factors to realize the research of coal rock breakage morphology and cutting force of coal and rock planer. The results show that the size of coal debris is related to the cutting depth of coal and rock, and increases with the increase of cutting depth, but with the increase of cutting speed, the variation trend of coal debris is not obvious, and the coal and rock are affected by a 30 擄planer. With the increase of cutting speed and cutting depth, the load of planer with 30 擄angle increases linearly.
【作者單位】： 遼寧工程技術大學機械工程學院;遼寧工程技術大學先進制造技術研究院;
【基金】：國家自然科學基金資助項目(51304105) “十二五”國家科技支撐計劃資助項目(2012BAF12B08) 遼寧省科技計劃資助項目(20131043)
【分類號】：TD421

【相似文獻】

相關期刊論文 前5條

1 付保英;胡瑞玲;;階梯刨削機的創新設計[J];煤礦機械;2011年08期

2 郝繼斌;;高效率碳弧氣刨槍[J];焊接;1984年05期

3 譚南林;提高曲面刨削加工精度的研究[J];機械制造;1996年02期

4 И.B.古謝夫,A.H.卡沙葉娃,胡廉;利用龍門斍床功率的問題[J];機床與工具;1955年21期

5 ;[J];;年期

，

本文編號：2134289