發布時間：2018-08-28 17:55

【摘要】：本文介于金昊空壓機廠單螺桿壓縮機漏油嚴重的現象，設計出雙列反向螺旋槽上游泵送機械密封，對其進行了解析計算，并運用有限元軟件ANSYS及FLUENT，對穩態密封環的溫度場、穩態端面之間的壓力場進行了模擬，得出了該密封環的壓力場、溫度場分布。研究了不同的摩擦副配對材料、密封介質壓力、主軸轉速等對密封端面溫度的影響；并討論了密封腔壓力、轉速、密封介質的粘度對機械密封的一些穩定性能參數的影響，為設計、優化機械密封提供了理論指導作用。模擬結果證明了該設計的正確性，變轉速或變壓力條件下，所設計的新型密封性能良好,端面溫升及摩擦功耗都較低，較普通的機械密封性能好，較單列的螺旋槽上游泵送機械密封性能也有所改善，滿足工業的應用要求。最后對新型機械密封進行了經濟性的分析，使其在功能和經濟上均達到要求。同時，，本文對于解決其他機械密封的泄露問題，具有一定的指導意義和應用價值。
[Abstract]:In this paper, due to the serious oil leakage of single screw compressor in Jinhao Air Compressor Plant, a double-row reverse spiral groove upstream pumping mechanical seal is designed and calculated analytically, and the temperature field of steady sealing ring is calculated by using finite element software ANSYS and FLUENT,. The pressure field and temperature field of the seal ring are simulated. The effects of different friction pairs on the temperature of seal end surface, such as the pressure of sealing medium, the pressure of sealing medium and the rotational speed of spindle, are studied, and the effects of pressure of seal chamber, speed of seal and viscosity of sealing medium on some stable performance parameters of mechanical seal are discussed. It provides theoretical guidance for the design and optimization of mechanical seals. The simulation results prove the correctness of the design. Under the condition of variable rotational speed or variable pressure, the new seal designed has good performance, the end surface temperature rise and friction power consumption are lower, and the performance of mechanical seal is better than that of common mechanical seal. Compared with single row spiral groove upstream pumping mechanical seal performance is also improved to meet the industrial application requirements. Finally, the economic analysis of the new mechanical seal is carried out to make it meet the requirements in function and economy. At the same time, this paper has certain guiding significance and application value for solving the leakage problem of other mechanical seals.
【學位授予單位】：遼寧工程技術大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TH136

【參考文獻】

相關期刊論文 前10條

1 沈錫華;;機械密封摩擦副端面的熱應力計算[J];北京化工學院學報;1980年03期

2 宋亞?wèn)|,孫曉光,周慶華;機械密封環溫度場的研究[J];國外油田工程;1994年06期

3 郝木明,胡丹梅,郭潔;新型上游泵送機械密封的性能研究[J];化工機械;2001年01期

4 彭旭東,謝友柏,顧永泉;機械密封端面溫度的確定[J];化工機械;1996年06期

5 顧永泉;機械密封的相似準數[J];化工機械;1997年04期

6 陳鐵鑫;白蘭璧;李繼和;;波紋管型機械密封動密封環的變形分析[J];流體工程;1985年07期

7 李紅,吳文林,趙忠祥,李克永;機械密封環溫度場的理論計算[J];流體工程;1986年08期

8 王建榮,顧永泉,陳弘;圓弧槽氣體潤滑非接觸式機械封密的特性[J];流體工程;1991年03期

9 陳文毅;李學虎;管洪;;機械密封溫度場的有限元計算法[J];流體工程;1991年10期

10 李鯤,王春揚,劉志國,曹旺順 ,張軍;機械密封環端面力變形的靜態測量方法研究[J];流體工程;1992年12期

相關碩士學位論文 前2條

1 蔣小文;螺旋槽干氣密封數值模擬及其槽形參數優化[D];南京工業大學;2004年

2 張建奎;丙烷泵用新型非接觸式機械密封的研究及應用[D];中國石油大學;2007年

本文編號：2210131