本文選題：回轉接頭 + 耐久性試驗��； 參考：《液壓與氣動》2016年06期

【摘要】：為了測試回轉接頭的內泄漏、外泄漏、及回轉接頭各零件的強度,根據回轉接頭的加載要求,確定了回轉接頭的液壓加載方法,采用了壓降法測量回轉接頭的微小內泄漏,并推導了內泄漏量計算公式,提高了測量準確度、縮短了試驗時間。構建了回轉接頭液壓加載系統,采用高壓發生器使回轉接頭高壓通道壓力長時間穩定在42 MPa,同時系統可以對回轉接頭高壓通道、低壓通道進行循環冷卻,避免了回轉接頭溫升過高,驅動電機卡死。系統滿足耐久性試驗對回轉接頭加載的要求,為國內回轉接頭耐久性試驗方法及設備研究提供了參考。
[Abstract]:In order to test the internal leakage, external leakage and the strength of the parts of the rotary joint, the hydraulic loading method of the rotary joint is determined according to the loading requirements of the rotary joint. The pressure drop method is used to measure the tiny internal leakage of the rotary joint. The calculation formula of internal leakage is deduced, which improves the accuracy of measurement and shortens the test time. The hydraulic loading system of the rotary joint is constructed. The pressure of the high pressure channel of the rotary joint can be stabilized at 42 MPa for a long time by using a high pressure generator. At the same time, the system can cycle cooling the high pressure channel and the low pressure channel of the rotary joint. Avoid too high temperature rise of rotary joint, drive motor stuck. The system meets the requirements of durability test for rotary joint loading and provides a reference for the research of domestic test method and equipment of rotary joint durability.
【作者單位】： 南京林業大學機電工程學院;中國重型機械研究院股份公司;
【基金】：江蘇省“六大人才高峰”項目(第七批次) 校企合作項目(208003129)
【分類號】：TH137

【相似文獻】

相關期刊論文 前6條

1 孫宏偉,苗明;起重機中心回轉接頭的改進[J];工程機械與維修;1996年03期

2 劉朋;董萬瑩;李永奇;尹立松;;中央回轉接頭性能試驗臺的對比研究[J];液壓氣動與密封;2014年07期

3 李海英;石川島起重機中心回轉接頭常見故障與預防[J];工程機械與維修;1998年04期

4 劉偉,冀曉輝,王慶國;輸油臂回轉接頭的設計[J];起重運輸機械;2004年05期

5 李陽;陳惠明;;ANSYS在中央回轉接頭性能測試中的應用[J];鹽城工學院學報(自然科學版);2011年02期

6 ;[J];;年期

相關碩士學位論文 前1條

1 刁煜晨;挖掘機中央回轉接頭型式檢驗方法研究[D];浙江大學;2013年

，

本文編號：1925488