本文選題：ANSYS + 振動給料機�。� 參考：《昆明理工大學》2011年碩士論文

【摘要】：振動給料機在礦山、冶金等各個領域都有廣泛的應用,振動給料機的穩定性和工作效率的提高對礦山給料系統的效率提高都用重大的意義�，F(xiàn)在,振動給料機正向著高精度、高效率的方向發展,因此對給料機在動態特性方面的高要求有著重要的意義。在生產實踐的過程中,振動給料機容易出現減震彈簧損壞、懸掛的金屬件損壞、樓面基礎振動較為激烈且電機較容易破壞等故障。因此,我們需要對振動給料機進行動力學分析,找出原因,為進一步改進振動給料機提供良好的基礎。 本文結合攀枝花鋼鐵集團有限公司選礦廠的實際生產情況,為了提高自同步振動給料機的生產穩定性和改善振動給料機的動態特性,進行了必要的研究。主要工作是對GZG2006型號的自同步振動給料機的給料槽和減震彈簧系統進行動力學分析與研究。 本文所用的限元分析軟件是ANSYS。在進行分析之前,首先是建立了GZG2006型號的自同步振動給料機的給料槽部分、減震彈簧部分、等效電機的部分以及整個系統的動力學有限元模型。然后對建立的動力學有限元模型進行動力學分析研究。具體的工作如下： 首先,運用三維建模軟件UG,對振動給料機系統進行了三維實體建模。再完成三維實體建模之后,運用有限元分析軟件中的網格劃分模塊對其進行網格劃分,生成有限元模型、以便后面計算之用。 其次,在模態分析選用利用Block Lanczos算法對自同步振動給料機有限元模型進行有限元模態分析計算,得出振動給料機的的前20階固有頻率和固有振型。通過分析,振動給料機的耦合振動情況有了較清晰的了解。 第三,在已經完成的模態分析計算的基礎上,應用ANSYS軟件的諧響應分析模塊對振動給料機進行諧響應分析。諧響應分析可以求出系統的幅頻動態響應曲線,得出到的結論是：振動給料機將可能在8Hz時12Hz和24Hz三個頻率點附近產生共振情況。 最后,對振動給料機進行了不同工況下的瞬態響應分析,主要進行空載工況下的瞬態分析和在拋擲給料工況下的瞬態分析。求出了關鍵節點的應力曲線和位移響應曲線和關鍵時間的振動給料機的振型圖、位移圖和應力圖,對振動給料機在工作狀況時的各種參數有了具體的了解。
[Abstract]:Vibrating feeder is widely used in mine metallurgy and other fields. The improvement of stability and working efficiency of vibrating feeder is of great significance to the improvement of efficiency of mine feed system. At present, vibrating feeder is developing towards high precision and high efficiency, so it is of great significance to require high dynamic characteristics of feeder. In the process of production, vibration feeder is prone to vibration absorber spring damage, hanging metal parts damage, floor foundation vibration is more intense and motor is easy to destroy and so on. Therefore, we need to analyze the vibration feeder dynamics, find out the cause, and provide a good foundation for further improvement of vibration feeder. Based on the actual production situation of Panzhihua Iron and Steel Group Co., Ltd., in order to improve the production stability of self-synchronous vibrating feeder and improve the dynamic characteristics of vibrating feeder, the necessary research has been carried out in this paper. The main work of this paper is to analyze and study the dynamics of feed slot and shock absorber spring system of GZG2006 self-synchronous vibration feeder. The finite element analysis software used in this paper is ANSYS. Before the analysis, the dynamic finite element models of the feed slot, the shock absorber spring, the equivalent motor and the whole system of the GZG2006 self-synchronous vibration feeder are established. Then the dynamic finite element model is studied. The specific work is as follows: Firstly, the three-dimensional solid model of vibrating feeder system is built by using three-dimensional modeling software UG. After the 3D solid modeling is completed, the finite element model is generated by using the mesh generation module in the finite element analysis software. Secondly, in modal analysis, Block Lanczos algorithm is used to calculate the finite element model of self-synchronous vibration feeder, and the first 20 natural frequencies and modes of vibration feeder are obtained. Through analysis, the coupling vibration of vibrating feeder is clearly understood. Thirdly, on the basis of the modal analysis and calculation, the harmonic response analysis module of ANSYS software is used to analyze the harmonic response of the vibrating feeder. The dynamic response curve of the system can be obtained by harmonic response analysis. It is concluded that the vibration feeder will produce resonance near the three frequency points of 12Hz and 24Hz during 8Hz. Finally, the transient response of the vibrating feeder under different conditions is analyzed, mainly under the no-load condition and the transient analysis under the condition of throwing the feedstock. The stress curve and displacement response curve of the key node and the vibration mode diagram, displacement diagram and stress diagram of the vibration feeder at the critical time are obtained, and the various parameters of the vibrating feeder in the working condition are understood concretely.
【學位授予單位】：昆明理工大學
【學位級別】：碩士
【學位授予年份】：2011
【分類號】：TH237.1

【參考文獻】

相關期刊論文 前10條

1 聞邦椿,關立章;空間單質體與雙質體自同步振動機的同步理論[J];東北工學院學報;1980年01期

2 王德石,呂志強;電磁振動給料機的研究與制造[J];海軍工程學院學報;1998年03期

3 于月民,丁元柱;電磁振動給料機的振動分析[J];煤礦機械;2000年12期

4 劉育;國內煤礦振動給料設備的現狀及發展[J];煤礦機械;2003年04期

5 王運池;國內振動給料設備的現狀與發展[J];煤質技術;2003年04期

6 聞邦椿;直線振動機物料運動的基本特征及運動學參數的選擇與計算[J];起重運輸機械;1974年04期

7 聞邦椿;共振運輸機與共振篩的動力學特性及改善其工作性能的措施[J];起重運輸機械;1975年Z1期

8 聞邦椿;計算振動輸送機、電振給料機和振動篩的物料平均速度與生產能力[J];起重運輸機械;1980年05期

9 李俊,金咸定,李維揚;瞬態接觸-沖擊問題的有限元分析[J];上海交通大學學報;1997年11期

10 高志剛;劉澤明;李娜;;復雜模型的ANSYS有限元網格劃分研究[J];機械工程與自動化;2006年03期

，

本文編號：1779955