本文選題：進給機構　切入點：強度校核　出處：《武漢理工大學》2011年碩士論文　論文類型：學位論文

【摘要】：隨著科技的進步與經濟的發展,鋼鐵產業作為國家經濟的支撐產業之一,逐步走向繁榮。在鋼鐵生產與加工過程中,熱處理工藝不僅是一道重要工序,還是提高材料強度最重要的手段。大型鋼板進給機構是將鋼板輸送到加熱爐中進行熱處理的設備,設備運轉的好壞,直接影響鋼板加工的效率。人們往往將進給機構作為多種熱處理設備之一進行研究,然而專門針對進給機構的研究甚少。隨著現代社會對高強度鋼板需求的增加,鋼板進行熱處理的要求也會越來越多,鋼板進給機構使用的頻率就會隨著提高,無論從安全方面和還是從經濟方面考慮,對進給機構結構的研究都是很有必要的。 首先,本文從力學的有關理論知識著手,著重研究了某進給機構的運動和受力情況,闡述了結構力學、有限元分析理論與方法、有限元分析軟件,以及可靠性分析理論及方法等理論方面的知識。其次,通過對進給機構的運動和受力分析以及基于ANSYS的有限元分析,計算分析出進給機構中不合理的設計,由此對進給機構的設計作出調整。最后,對新的方案進行運動和受力分析以及強度校核,重點對改進后的方案進行基于蒙特卡羅法的有限元法可靠性分析,得出在置信度為95%的條件下,改進后的大型鋼板進給機構的翻轉臂、主軸及車架所受應力值都小于其屈服強度,結構可靠。
[Abstract]:With the progress of science and technology and the development of economy, the iron and steel industry, as one of the supporting industries of the national economy, has gradually become prosperous. In the process of steel production and processing, heat treatment is not only an important process, It is also the most important means to improve the strength of the material. The feeding mechanism of large steel plate is the equipment for heat treatment of the steel plate in the heating furnace, and the equipment is good or bad in operation. The feed mechanism is often regarded as one of the kinds of heat treatment equipment, but the research on the feed mechanism is very few. With the increasing demand of high strength steel plate in modern society, the efficiency of steel plate processing is directly affected. The requirement of heat treatment of steel plate will be more and more, and the frequency of the feed mechanism will increase with the increase of the frequency. It is necessary to study the structure of the feed mechanism both from the safety and economic aspects. First of all, based on the theory of mechanics, this paper mainly studies the movement and force of a certain feed mechanism, expounds the structural mechanics, the theory and method of finite element analysis, the software of finite element analysis. Secondly, through the motion and force analysis of the feed mechanism and the finite element analysis based on ANSYS, the unreasonable design of the feed mechanism is calculated and analyzed. So the design of the feed mechanism is adjusted. Finally, the motion and force analysis and strength check of the new scheme are carried out, and the reliability analysis of the improved scheme based on the finite element method based on Monte Carlo method is emphasized. It is concluded that under the condition of confidence of 95%, the stress values of the overturning arm, the spindle and the frame of the improved large steel feed mechanism are less than its yield strength, and the structure is reliable.
【學位授予單位】：武漢理工大學
【學位級別】：碩士
【學位授予年份】：2011
【分類號】：TG155;TH22

【參考文獻】

相關期刊論文 前7條

1 寧連旺;;ANSYS有限元分析理論與發展[J];山西科技;2008年04期

2 貢金鑫,趙國藩;國外結構可靠性理論的應用與發展[J];土木工程學報;2005年02期

3 韓永勝;梁秋生;;ANSYS在重力壩應力分析中的應用[J];山東水利職業學院院刊;2009年02期

4 陳文瑛;吳穹;王勇毅;;機械安全性評估方法研究[J];中國安全科學學報;2010年01期

5 ;Reliability Assessment of Microgrid Using Sequential Monte Carlo Simulation[J];Journal of Electronic Science and Technology;2011年01期

6 桂樹國;;基于ANSYS參數化設計語言APDL的產品結構優化設計[J];組合機床與自動化加工技術;2010年07期

7 劉江;;淺談有限元理論在橋梁工程中的應用[J];科技資訊;2006年13期

相關碩士學位論文 前3條

1 吳啟和;基于結構可靠度理論的鋼筋混凝土梁橋的健康評估[D];西南交通大學;2006年

2 張榮花;基于可靠性理論的立式儲罐地震易損性研究[D];大慶石油學院;2009年

3 譚立娟;結構可靠性分析及基于響應面法的工程應用研究[D];山東大學;2010年

，

本文編號：1637125