本文關鍵詞：齒面接觸閃溫對齒輪嚙合特性的影響分析　出處：《制造業自動化》2016年03期 　論文類型：期刊論文

  更多相關文章： 齒面接觸閃溫 齒廓形變 嚙合剛度 分析

【摘要】：齒輪嚙合過程中能量損耗引起的齒廓形變改變了齒輪嚙合狀態,基于Bloke閃溫理論,推導出了齒面接觸閃溫隨齒輪嚙合點位置變化的表達式,計算了齒面接觸閃溫引起的齒廓形變;通過Hertz接觸理論,推導出齒面接觸閃溫對嚙合剛度的影響表達式。對模型進行研究,分析了摩擦因素隨嚙合點位置的變化規律,載荷、轉速對齒面最大接觸閃溫的影響,齒面接觸閃溫對齒廓形變和嚙合剛度的影響。仿真結果顯示,齒面接觸閃溫對輪齒嚙合剛度的影響較大,在非線性動力學分析中應予以考慮。
[Abstract]:The tooth profile deformation caused by the energy loss changes the gear meshing state. Based on the Bloke flash temperature theory, the expression of the tooth surface contact flash temperature with the gear meshing point position is derived. The tooth profile deformation caused by contact flash temperature on tooth surface is calculated. Through the Hertz contact theory, the influence expression of tooth surface contact flash temperature on meshing stiffness is deduced. The model is studied, and the variation law and load of friction factor with the position of meshing point are analyzed. The effect of the rotational speed on the maximum contact flash temperature of the tooth surface and the influence of the tooth surface contact flash temperature on the tooth profile deformation and meshing stiffness. The simulation results show that the tooth surface contact flash temperature has a great effect on the gear tooth meshing stiffness. It should be considered in nonlinear dynamic analysis.
【作者單位】： 蘭州交通大學;
【基金】：國家自然科學基金項目(11262009)
【分類號】：TH132.41
【正文快照】： 0引言齒輪傳動時應用廣泛的動力傳遞裝置之一。由于摩擦的存在,漸開線齒輪齒廓在嚙合傳動過程中能量的損耗大部分轉化為熱量,導致嚙合點處的齒廓溫度瞬間升高。在高速重載潤滑不良的工況下,齒面局部高溫導致齒面膠合引起傳動失效。齒廓瞬間升溫(齒面接觸閃溫)同時導致齒廓形變

【相似文獻】

相關期刊論文 前10條

1 孫殿柱,董學朱;描述真實齒面數學模型的研究[J];農業機械學報;2000年01期

2 劉祖愈;品良;;齒，

本文編號：1372603