本文選題：USB2.0 + TRANSEVEIVER�。� 參考：《復旦大學》2012年碩士論文

【摘要】：USB2.0OTG(USB On-The-Go)技術是USB2.0的發展與完善,具有USB2.0OTG接口的便攜式設備擺脫了對PC機的依賴,可以實現兩個非PC設備的直接通信并支持通信過程中主機和外設角色的相互切換；它同時符合USB2.0協議,最高傳輸速度可達480Mbps。USB2.0OTG在USB2.0的基礎上了增加了SRP(會話請求協議)和HNP(主機交換協議)。 USB2.0協議,USB2.0OTG補充協議以及UTMI+協議是整個電路設計的基礎,通過學習,理解了USB2.0OTG的工作原理,并在整個項目中承擔了OTG模塊的設計和TRANCEIVER模塊中接收電路的設計。 本文設計的OTG模塊包括三個電壓比較器,SRP電路以及工D檢測電路。三個電壓比較器閾值為：4.6v,1.4v,0.5v,分別用來指示VBUS電壓是否有效,A_device和B-device SRP電壓是否有效以及B-device SRP的初始化情況；SRP電路可以通過下拉電阻給VBUS放電以達到SRP的初始化條件而通過上拉電阻充電來發起SNP;ID檢測電路可以指示插入插頭的類型,判斷相連設備的角色。 本文討論了USB2.0接口電路的構成與基本原理,并重點闡述了高速數據接收電路和包絡信號檢測電路的設計,并給出了相關仿真。
[Abstract]:USB2.0OTG(USB On-The-Gois technology is the development and perfection of USB2.0. Portable devices with USB2.0OTG interface can get rid of the dependence on PC, and can realize direct communication between two non-PC devices and support the switch between host and peripheral roles in the communication process. It also conforms to the USB2.0 protocol, and the maximum transmission speed of 480Mbps.USB2.0OTG is increased based on USB2.0 (session request Protocol) and HNP (Host Exchange Protocol). USB2.0 protocol, USB2.0OTG supplementary protocol and UTMI protocol are the basis of the whole circuit design. Through studying, we understand the working principle of USB2.0OTG, and undertake the design of OTG module and the receiving circuit in TRANCEIVER module in the whole project. The OTG module designed in this paper includes three voltage comparators and D detection circuits. The threshold of the three voltage comparators is: 4.6v / 1.4v / 0.5 v. respectively, which indicates whether the VBUS voltage is effective or not and whether the B-device SRP voltage is effective or not, and the initialization of the B-device SRP circuit can discharge the VBUS by pull-down resistor to reach the initialization condition of SRP. The SNPID detection circuit is initiated by charging the pull up resistor to indicate the type of plug to be inserted. Judge the role of the connected device. In this paper, the structure and basic principle of USB2.0 interface circuit are discussed, and the design of high speed data receiving circuit and envelope signal detecting circuit are emphasized, and the related simulation is given.
【學位授予單位】：復旦大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TP336;TN710

【參考文獻】

相關期刊論文 前3條

1 王卉;王小軍;;可重用IP核設計技術研究[J];電子器件;2006年01期

2 李希文,白小平,宋明;通用串行總線收發器MIC2550及其應用[J];國外電子元器件;2001年07期

3 黃亮;應建華;沈緒榜;黃培;;USB Flash Memory Disk Drive系統模型[J];計算機與數子工程;2003年06期

，

本文編號：1822587