本文關鍵詞：低壓鑄造縮孔縮松判據預測技術，，由筆耕文化傳播整理發布。

首頁 > 專家 > 內容

文獻名稱：低壓鑄造縮孔縮松判據預測技術

    前言：本文考慮了壓力對臨界固相率的影響 ,提出了壓力下的縮孔預測判據 ,及與壓力、溫度梯度和冷卻速度相關的縮松預測判據 ,該判據已成功的應用于華北工學院鑄造工程中心開發的Castsoft軟件的低壓鑄造模塊
    In this paper, the influence of the pressure on the critical solid fraction was considered; the critical solid fraction method under the pressure condition was proposed to predict porosity. On the other hand, based on the darcy law, a new shrinkage prediction method related to pressure, temperature gradient and cooling rate was put out. The criterion had been successfully applied in the low-pressure casting module of castsoft, which had been developed by the casting centre of North China Institute of Techno...

文獻名稱 低壓鑄造縮孔縮松判據預測技術

Article Name
英文(英語)翻譯 The Technology of the Prediction of Shrinkage and Porosity during Low Pressure Casting Process;

作者 侯華; 徐宏; 程軍;

Author HOU Hua~1;XU Hong~1;CHENG Jun~2 （1.Dept. of Material Science and Engineering;North China Institute of Technology;Taiyuan 030051;China: 2.Department of （Science） &Technology;China North Industries Group Corporation;Beijing 100087;China）;

作者單位
Author Agencies 華北工學院材料科學工程系; 北方工業集團公司科技部 山西太原; 山西太原;

文獻出處
Article From 中國科學院上海冶金研究所; 材料物理與化學(專業) 博士論文 2000年度

關鍵詞 縮孔縮松預測; 低壓鑄造; 數值模擬;

Keywords Shrinkage and porosity prediction;Low-pressure casting;Numerical simulation;

鑄鋼件縮孔縮松預測方法及判據淺析
鋁合金鑄件縮孔縮松預測新技術
G/R~(1/2)法在球鐵件縮孔縮松預測中的應用研究
考慮充型過程的鑄鋼件縮孔縮松預測研究
鑄件凝固過程幾何模擬的縮孔縮松預測方法
鑄鋼件縮孔縮松預測的試驗研究
機車長轂輪芯鑄件縮孔縮松預測
收縮勢法在三維鑄件縮孔縮松預測中的應用
鈦合金立式離心精密鑄造縮孔縮松預測
氣囊左下支座熔模鑄造縮孔預測及應用

  本文關鍵詞：低壓鑄造縮孔縮松判據預測技術，由筆耕文化傳播整理發布。