本文選題：等離子噴涂 + YSZ涂層�。� 參考：《焊接學報》2017年01期

【摘要】：采用等離子噴涂方法在Ni718合金表面制備氧化釔穩(wěn)定氧化鋯(YSZ)涂層,通過在YSZ噴涂粉末中分別加入10%,30%和50%(質量分數,%)表面包覆Ti O2的聚苯酯材料,涂層平均孔隙率從原來的2.1%分別提高到12.3%,28.5%和29.7%,孔隙的平均直徑從原來的4.2μm分別變?yōu)?4.4,18.5和25.4μm.隨著孔隙的增多,涂層的表面洛氏硬度下降,同時涂層在刮磨過程中的摩擦力和摩擦系數下降.當孔隙率由2.1%上升到30%左右時,涂層在刮磨過程中的磨耗質量上升3倍左右,相對應的轉動銷質量損失下降約50%.結果表明,孔隙率的提高使得涂層的可磨耗性上升.
[Abstract]:Yttrium oxide stabilized zirconia (YSZ) coating was prepared on the surface of Ni718 alloy by plasma spraying. By adding 10%, 30% and 50% (mass fraction,%) surface of polyphenyl ester with Ti O2, the average porosity of the coating was increased from 2.1% to 12.3%, 28.5% and 29.7%, respectively, from the original 2.1%. The average diameter of the pores was 4 from the original YSZ. .2 mu m changed into 14.4,18.5 and 25.4 M. respectively. With the increase of pore, the surface Rockwell hardness of the coating decreased, while the friction and friction coefficient of the coating decreased. When the porosity increased from 2.1% to about 30%, the wear quality of the coating increased about 3 times in the scraping process, and the relative quality loss of the corresponding rotating pin decreased by about 50%. The results show that the wear resistance of the coating increases with the increase of porosity.

【作者單位】： 中國民航大學天津市民用航空器適航與維修重點實驗室;
【基金】：國家自然科學基金青年基金資助項目(51501222) 中央高�；究蒲袠I(yè)務經費中國民航大學專項基金資助項目(3122015L001) 中國民航局科技計劃資助項目(MHRD20160106)
【分類號】：TG174.4

【相似文獻】

相關期刊論文 前10條

1 周賢界;徐華蕊;;固體氧化物燃料電池用YSZ電解質納米粉體的濕法工藝進展[J];電工材料;2006年02期

2 范寶安,朱慶山,謝朝暉;固體氧化物燃料電池YSZ電解質薄膜的制備方法概述[J];過程工程學報;2004年01期

3 蘇蕙;吳也凡;;固體氧化物燃料電池YSZ電解質水系流延膜片的熱風干燥研究[J];陶瓷學報;2011年03期

4 賀天民,劉漢軍,楊景東,劉巍,劉志國,蘇文輝,呂U，

本文編號：1797686