本文選題：極薄帶軋制 + 彈性壓扁��； 參考：《鋼鐵》2017年01期

【摘要】：極薄帶在軋制及平整過程中,工作輥的彈性壓扁對軋制壓力的分布有很大影響,傳統的軋制力模型已經不再適用。為了在極薄帶板形板厚控制過程中得到準確的軋制力,Fleck提出了新的軋輥壓扁模型。針對Fleck模型進行試驗研究,同時進行有限元模擬分析。試驗過程中使用合金工具鋼軋輥,軋制不同厚度的軋件,通過顯微鏡測量變形區各部位的厚度,得到變形區軋輥的近似輪廓形狀。試驗與有限元模擬結果表明,隨著軋件厚度的減小,變形區出現了明顯的中性區,但是很難出現Fleck模型中提到的彈性卸載區,因此計算極薄帶軋制力時可以忽略中性區內的彈性卸載區以簡化軋制力模型。
[Abstract]:The elastic flattening of the work roll has a great influence on the distribution of rolling pressure in the rolling and leveling process of the extremely thin strip, and the traditional rolling force model is no longer applicable. A new roll flattening model was proposed in order to obtain an accurate rolling force in the process of strip thickness control. The Fleck model is tested and analyzed by finite element method. In the process of testing, the alloy tool steel roll is used to roll different thickness of workpiece. The thickness of each part of the deformation zone is measured by microscope, and the approximate contour of the roll in the deformation zone is obtained. The results of experiment and finite element simulation show that with the decrease of workpiece thickness, the deformation zone has obvious neutral zone, but it is difficult to find the elastic unloading zone mentioned in the Fleck model. In order to simplify the rolling force model, the elastic unloading zone in the neutral region can be neglected when calculating the rolling force of the very thin strip.
【作者單位】： 燕山大學國家冷軋板帶裝備及工藝工程技術研究中心;燕山大學機械工程學院;
【基金】：國家自然科學基金資助項目(51474190) 河北省自然科學基金資助項目(E2015203311)
【分類號】：TG331

【相似文獻】

相關期刊論文 前1條

1 高蕾;龐玉華;孫列;何艷兵;張進之;;熱連軋精軋帶鋼厚度預報模型優化研究[J];熱加工工藝;2013年11期

相關會議論文 前1條

1 時旭;劉相華;王國棟;李山青;許健勇;;冷軋薄帶鋼軋輥壓扁弧長的有限元分析[A];2005年全國計算材料、模擬與圖像分析學術會議論文集[C];2005年

相關碩士學位論文 前1條

1 王敬東;帶張力冷軋鈮、鈦短板的研究[D];東北大學;2008年

，

本文編號：1789098