本文選題：螺栓結合部　切入點：剛度　出處：《機械強度》2017年03期

【摘要】：螺栓結合部是機床結構中應用最普遍的固定結合部之一,直接影響著機床整機性能。應用有限元軟件分析機床整機結構性能時,為了保證計算精度,需要精細劃分螺栓結合部網格,導致計算規模大、耗時,因此探索簡單有效的機床螺栓結合部有限元模型的處理方法具有重要意義�；趯�(shí)驗獲取結合面基礎特性參數,通過解析方法得到螺栓結合部中每個單元螺栓結合部的六項剛度,然后基于剛度等效原則將每個單元螺栓結合部等效成對稱分布的四個彈簧單元,給出了等效彈簧剛度及位置的計算方法,在機床整機結構有限元分析時,以等效彈簧單元代替單元螺栓結合部,直接將其等效剛度代入有限元模型求解,可大大簡化有限元計算模型。實驗驗證該等效方法是可行的。
[Abstract]:Bolt joint is one of the most common fixed joints used in machine tool structure, which directly affects the performance of machine tool.When the finite element software is used to analyze the structural performance of the machine tool, in order to ensure the accuracy of the calculation, it is necessary to divide the mesh of the bolt joint in detail, which results in the large scale and time consuming of the calculation.Therefore, it is of great significance to explore a simple and effective finite element model for bolt joint of machine tool.Based on the experimental results, the basic characteristic parameters of the joint surface are obtained, and the six items of stiffness of each unit bolt joint in the bolt joint are obtained by analytical method.Then, based on the principle of stiffness equivalence, each element bolt joint is equivalent to four spring elements with symmetrical distribution, and the calculation method of equivalent spring stiffness and position is given. When the machine tool structure is analyzed by finite element method,The equivalent spring element is used to replace the element bolt joint, and its equivalent stiffness is directly replaced by the finite element model, which can greatly simplify the finite element model.The experimental results show that the equivalent method is feasible.
【作者單位】： 西安理工大學機械與精密儀器工程學院;甘肅民族師范學院;
【基金】：國家自然科學基金項目(51375370) 863項目(2012AA040701,2012AA040704) 陜西省機械制造裝備重點實驗室基金項目(14JS062)資助~~
【分類號】：TG502.31

【相似文獻】

相關期刊論文 前6條

1 朱乃彬;;高壓螺栓加工工藝對抗疲勞性能的影響[J];機械制造;1981年07期

2 馬杰;劉仲元;;預熱送風的座r[J];機械工人;1958年07期

3 陳亭志;;螺栓選型和裝配扭矩的計算方法研究[J];機械工程師;2014年06期

4 陶振賢 ,翟聲隆;零件聯接的幾種新方式[J];機械工程;1983年06期

5 崔國權,王波勇,王俊峰;大直徑螺紋上緊的一種有效方法[J];機械制造;2000年09期

6 ;[J];;年期

相關碩士學位論文 前1條

1 劉啟偉;基于ANSYS的螺栓固定結合面建模方法研究[D];東北大學;2008年

，

本文編號：1693224