本文選題：超聲沖擊　切入點：MB鎂合金　出處：《稀有金屬材料與工程》2017年07期

【摘要】：采用HJ-III型超聲沖擊設備對MB8鎂合金表面進行沖擊處理,利用高倍透射電子顯微鏡研究了超聲沖擊表層的微觀組織及晶粒細化機制。對經超聲沖擊處理和未沖擊處理的MB8鎂合金的耐磨性能進行了對比研究。采用掃描電鏡和顯微硬度計分別研究了超聲沖擊處理對磨損表面形貌和顯微硬度的影響。結果表明:超聲沖擊使MB8鎂合金的表面出現了嚴重的塑性變形,塑變層深度約為180μm,表面組織明顯得到細化。耐磨性能和顯微硬度隨超聲沖擊時間的延長而提高。與未沖擊試樣相比,在沖擊時間為6 min時,沖擊電流為1.2 A時,沖擊試樣的顯微硬度和耐磨性分別提高了102.8%和51.83%。
[Abstract]:The surface of MB8 magnesium alloy was treated with HJ-III ultrasonic impact equipment. The microstructure and grain refinement mechanism of ultrasonic impact surface layer were studied by high power transmission electron microscope (TEM). The wear resistance of MB8 magnesium alloy treated by ultrasonic impact treatment and non-impact treatment was compared and studied. Scanning electrolysis was used to study the wear resistance of MB8 magnesium alloy. The effects of ultrasonic impact treatment on the morphology and microhardness of worn surface were studied by mirror and microhardness tester respectively. The results showed that ultrasonic impact caused severe plastic deformation on the surface of MB8 magnesium alloy. The depth of the plasticized layer is about 180 渭 m, and the surface structure is obviously refined. The wear resistance and microhardness increase with the prolongation of the ultrasonic impact time. Compared with the non-impact specimen, the impact current is 1.2A when the impact time is 6 min. The microhardness and wear resistance of impact samples were increased by 102.8% and 51.833%, respectively.
【作者單位】： 華東交通大學;載運工具與裝備教育部重點實驗室;
【基金】：National Natural Science Foundation of China(51265013) Natural Science Foundation of Jiangxi Province(20151BAB206007)
【分類號】：TG146.22;TG663

【相似文獻】

相關期刊論文 前10條

1 孟獻民;顯微硬度試驗的對比性[J];兵器材料與力學;1984年03期

2 蔡兆勛;;全自動顯微硬度試驗系統[J];上海金屬.有色分冊;1992年03期

3 蔡厄,周平南;顯微硬度負荷依存性現象及其本質[J];上海交通大學學報;1998年02期

4 趙所琛,桂運平;顯微硬度的常量和相對比較測試方法[J];金屬學報;1979年01期

5 蔡s，

本文編號：1686588