本文關鍵詞：板材粘性介質壓力下的褶皺消除過程研究　出處：《沈陽航空航天大學》2016年碩士論文　論文類型：學位論文

  更多相關文章： 起皺 YBT 粘性介質 褶皺消除

【摘要】：起皺是影響薄壁鈑金零件成形精度的最主要因素之一,特別是隨著薄壁鈑金零件的廣泛應用,起皺問題更加容易產生,同時也受到了越來越多的重視。本文基于YBT實驗原理及粘性介質壓力成形特點,以不銹鋼SUS304為板材,采用有限元分析和實驗相結合的方法,進行了粘性介質壓力條件下的褶皺消除過程研究,確定了消皺過程中的影響因素及變形特點。首先,基于YBT原理設計了粘性介質壓力消皺實驗裝置,通過對褶皺形貌的評價,定義了褶皺消除率的概念,并對粘性介質壓力下褶皺消除過程的受力狀態進行了簡要理論分析,得出了不同受力狀態下褶皺變形特點。其次,應用有限元軟件ANSYS/LS-DYNA對不銹鋼SUS304粘性介質壓力下的褶皺消除過程進行分析,得到了粘性介質分子量對褶皺消除過程影響規律;確定了褶皺形貌及受力狀態對褶皺消除過程影響規律。最后,采用實驗方法對理論和有限元分析進行了驗證,進一步驗證了實驗裝置的可行性,以及粘性介質壓力下消皺過程的主要影響因素,實驗結果與理論分析結果吻合較好。
[Abstract]:Wrinkle is one of the most important factors that affect the forming accuracy of thin-walled sheet metal parts. Especially with the wide application of thin-walled sheet metal parts, wrinkling is more prone to occur, and more and more attention has been paid to it. In this paper, the experimental principle and YBT viscous pressure forming based on the characteristics of SUS304 stainless steel plate, using finite element analysis method combined with experiment, the process of elimination of medium pressure under the condition of viscous folds, the impact factors in the process of eliminating wrinkle and deformation characteristics. First of all, based on the principle of YBT design of viscous medium pressure wrinkle elimination experiment device, through the evaluation of the fold morphology, defines the fold elimination rate of the concept, and the viscous pressure under the fold stress eliminating state process gives a brief theoretical analysis, the deformation characteristics under different stress state of fold. Secondly, using the finite element software ANSYS/LS-DYNA on stainless steel SUS304 viscous pressure under the fold elimination process analysis, the viscous medium molecular weight to eliminate the influence of law of fold; to determine the state of the fold fold shape and influence process of eliminating stress. Finally, the experimental method is applied to verify the theoretical and finite element analysis, which further verifies the feasibility of the experimental device and the main influencing factors of the wrinkling process under viscous medium pressure, and the experimental results are in good agreement with the theoretical analysis.
【學位授予單位】：沈陽航空航天大學
【學位級別】：碩士
【學位授予年份】：2016
【分類號】：TG306

【相似文獻】

相關期刊論文 前7條

1 王哲;王忠金;;反向壓力對板材粘性介質壓力脹形的影響研究[J];材料科學與工藝;2009年06期

2 石笑萱;管箍接頭強度計算及應力分析[J];煤礦設計;1984年01期

3 高鐵軍;王忠金;;加載方式對黏性介質外壓縮徑成形的影響[J];模具工業;2009年01期

4 劉建光;王忠金;高鐵軍;;板材粘性介質壓力成形粘性附著力影響因素試驗研究[J];機械工程學報;2006年10期

5 高鐵軍;賀平;王忠金;;薄壁零件粘性介質外壓縮徑成形及數值模擬[J];機械設計與制造;2010年06期

6 王忠金;;難變形板材復雜形狀構件粘性介質壓力成形技術[J];航空制造技術;2014年10期

7 ;[J];;年期

相關重要報紙文章 前2條

1 周承惠;內腔介質壓力自補償密封技術[N];科技日?qǐng)?bào);2004年

2 陳強;用體內介質壓力作操控能源的閥門研發成功[N];中國工業報;2011年

相關博士學位論文 前1條

1 李毅;覆蓋件用6000系鋁合金粘性介質壓力成形性研究[D];哈爾濱工業大學;2009年

相關碩士學位論文 前1條

1 張鶴鵬;板材粘性介質壓力下的褶皺消除過程研究[D];沈陽航空航天大學;2016年

，

本文編號：1345920