發布時間：2018-12-23 08:52

【摘要】：隨著相關技術的飛速發展,LED的功率增長速度越來越快,產生的熱流密度越來越高,LED對創新、先進的散熱技術的需求越來越緊迫,對散熱技術的要求也越來越高,散熱問題一直以來都是制約LED發展的關鍵因素之一。由此可見,LED急需新一代散熱技術,該技術應該具備以下優點:高散熱效率,小重量,小體積,低成本,低噪音,低功耗,可集成度高,沒有運動部件等。離子風散熱技術具備這些優點,很可能成為滿足LED散熱的新一代散熱技術。本文基于電暈放電理論,設計了一種離子風發生裝置,裝置由針狀發射電極和網狀收集電極組成,其具備前面提到的各個優點,能與LED芯片高度集成,實現一體化封裝;同時,設計了實驗測試平臺,對影響離子風發生裝置性能的關鍵參數進行了研究,重點研究了發射電極形狀、收集電極形狀、電極間距和工作電壓等因素對離子風發生裝置的影響,針對散熱表面尺寸為40mm×40mm的高熱流密度LED芯片設計了離子風發生裝置陣列,進而設計出滿足LED芯片散熱需求的離子風散熱系統,同時,設計對比實驗,對比分析離子風散熱系統與傳統強制風冷散熱系統的散熱效果,具體研究?jī)?nèi)容與結論如下:1.采用紫銅作為發射電極和收集電極的材料,利用激光加工設備對0.1mm厚度的紫銅板進行激光加工,通過后期組裝制成離子風發生裝置,使用單一變量法對網狀收集電極網格尺寸、針狀發射電極直徑和電極間距等影響因素逐一展開實驗研究,結果表明:收集電極網格尺寸為1.0mm×1.0mm、發射電極直徑為0.122mm、電極間距為5mm是優選的結構參數,實現的最高風速達到2.45m/s。2.設計了一個適用于離子風發生裝置陣列性能測試的實驗平臺,通過控制單一變量,對離子風發生裝置陣列縱向間距、橫向間距,以及收集電極與散熱表面夾角等關鍵參數進行實驗研究,實驗結果顯示:優選的縱向間距為6mm,優選的橫向間距為2.64mm,收集電極與散熱表面夾角優選值為30°,實現的最低溫度為50.29°C。3.分別研究了不同熱流密度、不同工作電壓等因素對LED離子風散熱系統性能的影響,并設計對比實驗,對比分析離子風散熱系統與傳統強制風冷散熱系統的散熱效果,實驗結果表明:在0.3752cm W熱流密度下,系統的散熱效果最佳,實現的對流換熱系數最高可達到75.56W/(3　);當工作電壓為4.2k V時,系統的散熱效果良好,實現的對流換熱系數最高可達到66.71W/(3　);當功耗在0-0.026W時,離子風散熱系統占有絕對優勢,實現的對流換熱系數最高可達到51.30W/(3　)。本文為高熱流密度LED離子風散熱系統的設計、結構優化提供了新思路,對離子風散熱系統的傳熱特性和應用研究豐富了LED芯片熱管理的應用體系,為以LED芯片為代表的高熱流密度芯片的熱設計提供了新方案。
[Abstract]:With the rapid development of related technology, the power of LED is increasing faster and faster, and the heat flux is becoming higher and higher. The demand of LED for innovation and advanced heat dissipation technology is more and more urgent, and the requirement for heat dissipation technology is also more and more high. Heat dissipation has always been one of the key factors restricting the development of LED. Therefore, LED is in urgent need of a new generation of heat dissipation technology, which should have the following advantages: high heat dissipation efficiency, small weight, small volume, low cost, low noise, low power consumption, high integration, no moving parts, etc. Ion wind heat dissipation technology has these advantages, and it is likely to be a new generation of heat dissipation technology to meet the LED heat dissipation. Based on the theory of corona discharge, an ion wind generator is designed in this paper. The device is composed of needle-like emission electrode and net-shaped collection electrode. It has the advantages mentioned above, and can be highly integrated with LED chip to realize integrated encapsulation. At the same time, the experimental test platform is designed to study the key parameters that affect the performance of the ion wind generator, especially the shape of the emission electrode and the shape of the collecting electrode. The effect of electrode spacing and working voltage on the ion wind generator was studied. An array of ion wind generating devices was designed for a high heat flux LED chip with a heat dissipation surface size of 40mm 脳 40mm. Then we design the ion wind heat dissipation system which can meet the demand of LED chip. At the same time, we design the contrast experiment, compare and analyze the heat dissipation effect of ion wind cooling system and traditional forced air cooling heat dissipation system. The specific research contents and conclusions are as follows: 1. Using copper as the material of emission electrode and collecting electrode, the copper plate with 0.1mm thickness was processed by laser processing equipment, and the ion wind generating device was made through the later assembly. A single variable method was used to study the influence factors such as mesh size, needle emission electrode diameter and electrode spacing. The results showed that the grid size of the collecting electrode was 1.0mm 脳 1.0 mm, the diameter of the emission electrode was 0.122 mm, and so on. The electrode spacing of 5mm is the optimal structural parameter, and the maximum wind speed is 2.45 m / s. 2. An experimental platform for measuring the performance of ion wind generator array is designed. By controlling a single variable, the longitudinal and transverse spacing of ion wind generator array is calculated. The experimental results show that the optimized longitudinal distance is 6 mm, the optimal transverse distance is 2.64 mm, and the optimum angle between the collecting electrode and the heat dissipation surface is 30 擄. The realized minimum temperature is 50.29 擄C. 3. The effects of different heat flux and working voltage on the performance of LED ion cooling system were studied, and a comparative experiment was designed to analyze the effect of ion air cooling system and traditional forced air cooling system. The experimental results show that under the heat flux of 0.3752cm W, the heat dissipation effect of the system is the best, and the highest convection heat transfer coefficient can reach to 75.56W/ (3?). When the working voltage is 4.2 kV, the heat dissipation effect of the system is good, and the highest convection heat transfer coefficient can reach 66.71W/ (3?). When the power consumption is 0-0.026W, the ion wind heat dissipation system has the absolute advantage and the highest convection heat transfer coefficient can reach 51.30W/ (3?). This paper provides a new idea for the design and structure optimization of LED ion cooling system with high heat flux. The research on heat transfer characteristics and application of ion wind cooling system enriches the application system of LED chip thermal management. It provides a new scheme for heat design of high heat flux chip represented by LED chip.
【學位授予單位】：廣東工業大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TN312.8

【參考文獻】

相關期刊論文 前10條

1 王靜;蔡憶昔;包偉偉;李慧霞;;針-網式離子風發生器的散熱研究[J];鄭州大學學報(工學版);2016年03期

2 王長宏;謝澤濤;鄒大樞;邢瑞林;;大功率LED散熱器的數值模擬與優化[J];電子元件與材料;2015年06期

3 張任平;孫健;汪和平;馮青;;空氣強制對流冷卻工況下多芯片散熱過程數值模擬[J];低溫與超導;2015年03期

4 趙矗;張劍飛;何雅玲;陶文銓;;離子風強化平板對流傳熱的數值模擬[J];工程熱物理學報;2014年03期

5 晏建宇;王雙喜;劉高山;葉家星;;大功率LED散熱技術研究進展[J];照明工程學報;2013年05期

6 郭凌曦;左敦穩;孫玉利;周馳;方鈺;;LED散熱技術及其研究進展[J];照明工程學報;2013年04期

7 沈忠良;盧冰;李思文;鐘英杰;;大功率LED強化散熱技術進展[J];輕工機械;2013年02期

8 王維;楊蘭均;高潔;劉帥;;多針-網電極離子風激勵器推力與推功比的實驗研究[J];物理學報;2013年07期

9 賈艷婷;徐昌貴;閆獻國;田志峰;;半導體制冷研究綜述[J];制冷;2012年01期

10 李慶;李海鳳;孫曉榮;張文月;王昊;;電暈放電電流體狀態實驗研究與數值模擬[J];高電壓技術;2010年11期

相關碩士學位論文 前3條

1 黃炯桐;大功率LED平板熱管散熱系統的性能研究[D];廣東工業大學;2016年

2 郭凌曦;大功率LED光源散熱結構設計及其散熱性能研究[D];南京航空航天大學;2014年

3 梁雪艷;大功率LED液冷散熱系統的研究[D];浙江大學;2012年

，

本文編號：2389729