【摘要】：熱光可調諧濾波器是一種新的光學器件,在光纖通信、激光調諧、光譜分析以及紅外探測等諸多領域有著廣泛的應用。這種器件利用材料的熱光效應,可以實現中心波長移動的調諧濾波,具有調諧范圍大、工藝制作方便以及結構簡單的優點。針對濾波器性能實現器件結構設計、根據實驗條件確定濾波器的工藝實現方案以及濾波器結構中各膜層的變化均是對器件性能產生影響的關鍵所在,因此,本文利用理論分析濾波器的結構特性,在此基礎上進行優化和選擇,并從工藝上考慮并消除器件多層膜結構帶來的問題,制作出濾波器件進行測試,對熱光濾波器的應用技術進行初步探究。首先,通過對器件性能要求的分析確定合適的濾波器材料,從理論出發根據所選材料的參數對濾波器結構進行分析,確定濾波器基本結構為具有半波長的中間腔層的單腔體,并對器件的熱調諧性能進行了仿真研究,得到調諧靈敏度為0.1nm/℃。其次,通過分析器件對膜層的要求與工藝上實現的難點,解決多層膜沉積中的膜層應力、均勻性、各層接觸以及粗糙度問題,確定出制備各膜層的工藝參數,對濾波器制作過程中可能引起的誤差進行分析,在此基礎上完成單元濾波器的工藝制備。制備的樣品在1554 nm處獲得72%的透射率,SEM圖顯示器件中各膜層均勻連續且致密,沒有缺陷。利用搭建的熱光器件測試平臺對濾波器熱調諧性能進行測試,其中心波長移動明顯,調諧靈敏度達到0.072 nm/℃,并且在不同位置處熱響應變化不大,表現出良好的熱響應均勻性。最后,將單元濾波器通過光刻實現陣列化以探究熱光調諧濾波器應用技術,并對濾波器性能進行了表征分析,濾波器陣列分布均勻,尺寸保持一致,并通過溫度的變化控制濾波器的輸出光強,在光開關與探測領域展現出良好的應用前景,為后續研究打下基礎。
[Abstract]:Thermo-optical tunable filter is a new optical device, which has been widely used in many fields such as optical fiber communication, laser tuning, spectral analysis and infrared detection. By utilizing the thermo-optical effect of the material, the device can realize the tunable filter of center wavelength shift, which has the advantages of wide tuning range, convenient fabrication and simple structure. In order to realize the device structure design of filter performance, according to the experimental conditions, it is the key to determine the technological realization scheme of filter and the change of each film layer in the filter structure to influence the device performance. In this paper, the structure characteristics of the filter are analyzed theoretically, and the optimization and selection are carried out on this basis, and the problems caused by the multilayer membrane structure of the device are considered and eliminated in the process, and the filter parts are made for testing. The application technology of thermal optical filter is discussed. First of all, the suitable filter material is determined by analyzing the performance requirements of the device. The filter structure is analyzed according to the parameters of the selected material, and the basic structure of the filter is determined to be a single cavity with half a wavelength in the middle cavity. The thermal tuning performance of the device is simulated and the tuning sensitivity is obtained at 0.1nm/ 鈩，

本文編號：2261273