【摘要】：作為特高壓電網中的核心設備之一,特高壓交流變壓器的工程應用技術隨著特高壓電網建設步伐的加快受到了越來越多的關注。論文是在綜合分析目前國內外技術資料和總結以往實踐經驗的基礎上,對特高壓交流變壓器的設計選型以及現場安裝、試驗、調試環節的關鍵技術進行了研究與分析。 通過對變壓器整體結構型式、調壓方式、冷卻方式、變電容量、第三側電壓、阻抗電壓等內容的分析與研究,選擇了采用單相、自耦、本體變與調壓補償變分體布置的變壓器作為應用于工程實踐的特高壓交流變壓器,同時確定了采用中性點變磁通調壓方式和強迫油循環非導向冷卻方式以及變壓器容量、第三側電壓值、阻抗電壓值及內絕緣水平。通過對全密封絕緣油凈化處理系統的整體設計以及對濾油設備、絕緣油凈化處理方法的研究與分析,提出了全密封絕緣油凈化處理系統的配置要求、完善了其使用功能,優化了濾油方法,并對顆粒度指標控制提出了針對性措施,解決了工程現場對絕緣油指標控制嚴以及凈化工作量大的實際問題。通過對變壓器高壓出線裝置與高壓套管吊裝、抽真空與真空注油、熱油循環等安裝作業流程的分析,明確了高壓出線裝置與高壓套管的吊裝方法以及抽真空時間與真空度控制、注油速度與油溫控制、熱油循環時間控制等技術要求。通過對本體變、調壓補償變繞組連同套管的感應耐壓帶局放測量試驗的加壓程序、試驗判據的分析與試驗設備參數選擇的計算,提出了工程現場試驗工作步驟以及主要的抗干擾措施。通過對調壓補償變壓器差動保護電流互感器的極性分析,明確了差動保護配置要求,并對指定檔位下的平衡系數與差動電流進行了計算,同時完成了電流互感器極性變化準確性的現場校驗。通過對變壓器設計選型與現場安裝、試驗、調試各應用環節關鍵技術的研究與分析,對后續更進一步提升工程現場應用技術水平與變壓器長期安全運行都具有很重要的現實意義。
[Abstract]:As one of the core equipment in UHV power grid, the engineering application technology of UHV AC transformer has been paid more and more attention with the acceleration of UHV power grid construction. On the basis of synthetically analyzing the domestic and foreign technical data and summarizing the previous practical experience, this paper studies and analyzes the key technologies of the design, selection, field installation, test and debugging of UHV AC transformers. Through the analysis and research on the whole structure type of transformer, voltage regulation mode, cooling mode, transformer capacity, third side voltage, impedance voltage and so on, the single phase, auto coupling, etc. The transformer arranged by bulk transformer and voltage regulation compensation variable body is used as UHV AC transformer applied in engineering practice. At the same time, the neutral point variable flux regulation mode, forced oil cycle unguided cooling mode and transformer capacity are determined. Third side voltage, impedance voltage and internal insulation level. Through the research and analysis of the whole design of the purifying treatment system for the fully sealed insulating oil and the research and analysis of the oil filter equipment and the method of purifying and treating the insulating oil, the configuration requirements of the purifying treatment system for the fully sealed insulating oil are put forward, and the use function of the system is improved. The oil filter method is optimized, and the corresponding measures are put forward to control the particle size index, which solves the practical problems of strict control of insulation oil index and large amount of purification work in the engineering site. Through the analysis of the installation operation flow of transformer high-voltage outlet device and high-voltage casing, vacuum pumping and vacuum oil injection, hot oil circulation and so on, the hoisting method of high-voltage outlet device and high-voltage casing, as well as the vacuum time and vacuum degree control are defined. Oil injection speed and oil temperature control, hot oil cycle time control and other technical requirements. Through the pressurization program of the partial discharge measurement test of inductive pressure band, the analysis of test criterion and the calculation of parameter selection of test equipment, The working steps and main anti-interference measures are put forward. Through the polarity analysis of the differential protection current transformer of the voltage regulation compensation transformer, the configuration requirements of the differential protection are clarified, and the balance coefficient and differential current under the specified gear are calculated. At the same time, the accuracy of polarity change of current transformer is verified. Through the research and analysis of the key technologies of transformer design and selection, field installation, test and debugging, It is of great practical significance to further enhance the technical level of engineering field application and the long-term safe operation of transformers.
【學位授予單位】：華北電力大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TM41

【參考文獻】

相關期刊論文 前9條

1 李文軍;關于研制 1000kV 級特高壓變壓器若干問題的探討[J];變壓器;1997年05期

2 吳敬儒,徐永禧;我國特高壓交流輸電發展前景[J];電網技術;2005年03期

3 李光范;王曉寧;李鵬;孫麟;李博;李金忠;;1000kV特高壓電力變壓器絕緣水平及試驗研究[J];電網技術;2008年03期

4 張軍;張斌;劉華;李黎;張新旺;;全封閉集中式特高壓設備絕緣油處理系統[J];電網技術;2008年21期

5 張建坤;賀虎;鄧德良;周孚民;王志強;;特高壓變壓器現場安裝關鍵技術及應用[J];電網技術;2009年10期

6 楊寶祥;吳峽;;關于特高壓變壓器的一點思考[J];高電壓技術;2005年12期

7 郭慧浩;付錫年;;特高壓變壓器調壓方式的探討[J];高電壓技術;2006年12期

8 張章奎;;國內外特高壓電網技術發展綜述[J];華北電力技術;2006年01期

9 葉嚴軍;崔淑芳;;交流特高壓變壓器特點淺析[J];河南電力;2013年01期

，

本文編號：2311507