【摘要】：利用熔融共混法制備了聚酰胺6(PA6)/多層石墨烯復合材料并研究了其性能。結果表明,多層石墨烯具有明顯的成核作用,使PA6的結晶過程可在較高溫度下進行;降低了PA6的結晶速率,有利于生成熱力學更穩定的α型晶體。多層石墨烯提高了PA6的玻璃化轉變溫度,對PA6具有增強增剛作用,在多層石墨烯質量分?jǐn)?shù)為2.5%時,PA6拉伸強度增加了11.4%,彈性模量增加了29.3%,在多層石墨烯質量分?jǐn)?shù)為2%內對PA6沖擊強度基本沒有影響。
[Abstract]:Polyamide 6 (PA6) / multi-layer graphene composites were prepared by melt blending and their properties were studied. The results show that the multi-layer graphene has obvious nucleation effect, so that the crystallization process of PA6 can be carried out at higher temperature, and the crystallization rate of PA6 is reduced, which is beneficial to the formation of thermodynamic 偽-type crystals. Multi-layer graphene increased the glass transition temperature of PA6 and strengthened PA6. When the mass fraction of multi-layer graphene was 2.5%, the tensile strength and elastic modulus of PA6 increased by 11.4% and 29.3%, respectively. There was no effect on the impact strength of PA6 when the mass fraction of graphene was 2%.
【作者單位】： 江門職業技術學院;
【基金】：廣東省江門市科技計劃項目(江財工[2016]143號)
【分類號】：TB332;TQ342.11

【相似文獻】

相關期刊論文 前10條

1 ;浙江大學制得宏觀石墨烯長纖維[J];炭素技術;2012年01期

2 王嫻;;功能化石墨烯/聚合物基復合材料性能研究進展[J];合成材料老化與應用;2012年06期

3 王宏智;高翠俠;張鵬;姚素薇;張衛國;;石墨烯/聚苯胺復合材料的制備及其電化學性能[J];物理化學學報;2013年01期

4 張愛紅;張姣;林虹君;;石墨烯及氧化石墨烯在蛋白質檢測中的應用[J];生命的化學;2013年03期

5 牛祿青;;石墨烯:開啟碳時代?[J];新經濟導刊;2013年08期

6 張忠金;王瑩;關磊;;石墨烯的制備及其負載催化劑的應用研究進展[J];化學與黏合;2013年06期

7 沙建超;趙蘊華;羅勇;;基于專利的中美石墨烯技術創新比較研究[J];全球科技經濟w，

本文編號：2478419