本文選題：碳納米管(CNTs) + 納米碳化硅顆粒(SiC_p)　； 參考：《西安理工大學》2017年碩士論文

【摘要】：碳納米管(Carbon nanotubes,CNTs)增強鋁基復合材料(Aluminum matrix composites,AMCs)因集成鋁和CNTs各自的優異性能而得到廣泛關注。然而CNTs分散困難以及CNTs/Al界面反應控制問題是制約其發展的瓶頸。為解決以上問題,本文提出了低能濕法混合和CNTs-SiCp雙納米相增強AMCs的新研究思路。研究首先采用低速行星球磨(Planetary Ball Milling, PBM)制備了 CNTs/Al 及 CNTs-SiCp/Al 復合粉體,利用放電等離子燒結(Spark Plasma Sintering,SPS)技術對粉體進行固化,并經熱擠壓(Hot Extrusion,HE)制備獲得CNTs和CNTs-SiCp增強AMCs。通過熱力學分析、微觀組織觀察、界面微觀結構分析以及力學性能測試,闡明了燒結溫度、CNTs含量、SiC含量及雙納米增強相對AMCs組織及性能的影響規律。CNTs增強AMCs研究結果表明:630 ℃下燒結制備的AMCs經擠壓后相對密度均超過99%,達到完全致密化;CNTs含量不超過0.5 vol.%時,其在鋁基體中呈現均勻單獨分散狀態,實際增強效果與理論值相吻合;當CNTs含量超過0.5 vol.%時,CNTs容易在局部發生聚集形成團簇,從而導致孔洞及微裂紋等缺陷,弱化CNTs的增強效果,最終降低AMCs的力學性能、延性和導電性;微觀組織觀察表明:CNTs能夠有效地細化Al基體晶粒,并且隨CNTs含量增加晶粒細化效果更為明顯;界面微觀結構分析表明:當燒結溫度升至630 ℃時,CNTs與Al之間發生界面反應生成Al4C3,反應從CNTs外壁開始,CNTs內層仍然保持其原始管狀結構;力學性能測試結果表明:隨著燒結溫度的升高,AMCs的抗拉強度逐漸提高。通過對CNTs-Al體系的研究確定了合適的制備工藝,明確了在此制備條件下,CNTs含量高于0.5vol%時其容易發生團聚,從而導致AMCs力學性能和導熱導電性能下降,為CNTs-SiCp雙納米相增強AMCs的研究奠定了理論和實驗基礎。在對CNTs-Al體系研究的基礎上,本文提出引入納米SiCp作為第二增強相以促進CNTs強化效果的發揮。研究采用“超聲分散-PBM-SPS-HE”相結合的工藝制備了致密的CNTs-SiCp雙納米相增強AMCs。結果表明:SiCp的加入進一步促進了 CNTs的分散,改善了 CNTs與基體之間的潤濕性;SiC作為增強顆�？梢砸种凭Я５拈L大并阻礙位錯的運動起到細晶強化和彌散強化的作用;分布于CNTs周圍的SiCp可以通過釘扎作用抑制或延緩CNTs的拔出和剝離,進一步提升CNTs的強化效果,協助CNTs發揮強化作用;當兩種增強粒子相互協同作用時其增強效果明顯優于單一增強相,且雙納米相更有效地細化了晶粒。0.5CNTs-0.5SiCp/Al復合材料的抗拉強度達到247 MPa,相比于純Al ( σ b =127 MPa)提升了 94%,而相比于 1.OCNTs/Al ( σ b=217 MPa)和 1.0SiCp/Al ( σ b=158 MPa)也分別有14%和56%的提升。通過界面分析,發現在CNTs與Al基體之間存在納米級反應過渡層,顯著提高了界面結合強度,使載荷可以有效地從Al基體傳遞至增強體,從而顯著提升AMCs的強度。同時SiCp的存在也抑制了界面層的過度反應,使得AMCs強度提升的同時,能夠保持和純A1相近的延伸率(20%)和電導率(50%IACS)。CNTs-SiCp增強AMCs主要的強化機制包括載荷傳遞、細晶強化和彌散強化,其強化機制是CNTs和SiCp兩種納米增強相協同強化的結果。
[Abstract]:Carbon nanotube (Carbon nanotubes, CNTs) reinforced aluminum matrix composites (Aluminum matrix composites, AMCs) have been widely concerned for their excellent performance in the integration of aluminum and CNTs. However, the difficulty of CNTs dispersion and the control of CNTs/Al interface reaction are the bottlenecks that restrict its development. In order to solve the above problems, this paper proposes a low energy wet mixing and a mixture of low energy and moisture. The new research idea of CNTs-SiCp double nanometers enhanced AMCs was studied. Firstly, the composite powders of CNTs/Al and CNTs-SiCp/Al were prepared by low speed planetary ball milling (Planetary Ball Milling, PBM). The powder was cured by discharge plasma sintering (Spark Plasma Sintering, SPS). NTs-SiCp enhanced AMCs. through thermodynamic analysis, microstructure observation, interfacial microstructure analysis and mechanical properties testing, clarified the sintering temperature, CNTs content, SiC content and the influence of double nano on the relative AMCs microstructure and properties.CNTs enhanced AMCs research results showed that the relative density of AMCs prepared at 630 C was all after extrusion. More than 99%, achieve complete densification; when CNTs content is not more than 0.5 vol.%, it presents a uniform dispersion state in the aluminum matrix, and the actual enhancement effect is consistent with the theoretical value. When the content of CNTs exceeds 0.5 vol.%, CNTs is easily aggregated and formed in a local cluster, resulting in defects such as holes and micro cracks and weakens the enhancement effect of CNTs. The mechanical properties, ductility and conductivity of AMCs are reduced, and the microstructure observation shows that CNTs can effectively refine the grain of Al matrix, and the effect of grain refinement is more obvious with the increase of CNTs content. The interfacial microstructure analysis shows that when the sintering temperature rises to 630 C, the interfacial reaction between CNTs and Al generates Al4C3, and the reaction is opened from the outer wall of CNTs. In the beginning, the inner layer of CNTs still maintains its original tubular structure, and the results of mechanical properties test show that the tensile strength of AMCs increases with the increase of sintering temperature. The suitable preparation process is determined by the study of the CNTs-Al system. It is clear that when the content of CNTs is higher than 0.5vol%, it is easy to be reunion and thus leads to the AMCs force. The decline of the performance and the conductivity of thermal conductivity has laid a theoretical and experimental basis for the study of the CNTs-SiCp double nanomaterials enhanced AMCs. On the basis of the study of the CNTs-Al system, this paper introduces the introduction of nano SiCp as the second enhanced phase to promote the enhancement of the CNTs enhancement effect. The compact CNTs-SiCp double nanomaterials enhanced AMCs. results showed that the addition of SiCp further promoted the dispersion of CNTs and improved the wettability between the CNTs and the matrix, and SiC as an enhanced particle could inhibit the growth of grain and impede the motion of dislocation to enhance the crystallization and dispersion of the dislocation, and the SiCp around CNTs can pass through. The pinning effect inhibits or delays the exfoliation and stripping of CNTs, further improves the strengthening effect of CNTs and assists CNTs to exert its strengthening effect. When the two enhanced particles synergy with each other, the enhancement effect is obviously better than that of the single enhanced phase, and the double nanometers more effectively refine the tensile strength of the grain.0.5CNTs-0.5SiCp/Al composite to reach 247 MP. A, compared to pure Al (sigma B =127 MPa) increased by 94%, compared to 1.OCNTs/Al (sigma b=217 MPa) and 1.0SiCp/Al (sigma b=158 MPa) also 14% and 56%, respectively. Through the interface analysis, it was found that there was a nano reaction transition layer between the CNTs and the substrate, which significantly increased the interfacial bonding strength, so that the load could be effectively transmitted from the substrate. The strength of AMCs is greatly enhanced, and the presence of SiCp also inhibits the overreaction of the interface layer. While the strength of AMCs is enhanced, the main strengthening mechanisms of the extensibility (20%) and the conductivity (50%IACS).CNTs-SiCp enhanced AMCs, which are similar to pure A1, include load transfer, fine grain strengthening and dispersion strengthening, and its strengthening The mechanism is the result of the synergistic enhancement of two kinds of nano reinforcing phases of CNTs and SiCp.

【學位授予單位】：西安理工大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TB33

【參考文獻】

相關期刊論文 前10條

1 Ziyang Xiu;Wenshu Yang;Ronghua Dong;Murid Hussain;Longtao Jiang;YongXing Liu;Gaohui Wu;;Microstructure and Mechanical Properties of 45 vol.%SiC_p/7075Al Composite[J];Journal of Materials Science & Technology;2015年09期

2 謝敬佩;王行;王愛琴;郝世明;劉舒;;真空熱壓SiC_p/2024Al復合材料力學性能與顯微結構[J];材料熱處理學報;2015年01期

3 吳文杰;王愛琴;王榮旗;謝敬佩;;SiC顆粒增強Al-Si基復合材料的國內研究進展[J];粉末冶金工業;2014年06期

4 崔照雯;劉建金;王聰聰;梁棟;高鵬;賈成廠;;碳納米管和氧化鋁顆粒在銅基復合材料中的協同作用[J];粉末冶金技術;2014年05期

5 Hansang Kwon;Marc Leparoux;Akira Kawasaki;;Functionally Graded Dual-nanoparticulate-reinforced Aluminium Matrix Bulk Materials Fabricated by Spark Plasma Sintering[J];Journal of Materials Science & Technology;2014年08期

6 劉玫潭;凌嘉輝;劉家成;洪曉松;李國強;;SiC增強Al基復合材料的制備和性能[J];半導體光電;2014年03期

7 D.Wang;B.L.Xiao;Q.Z.Wang;Z.Y.Ma;;Evolution of the Microstructure and Strength in the Nugget Zone of Friction Stir Welded SiCp/Al-Cu-Mg Composite[J];Journal of Materials Science & Technology;2014年01期

8 湯金金;李才巨;朱心昆;;碳納米管增強鋁基復合材料的界面研究進展[J];材料導報;2012年11期

9 賀毅強;;顆粒增強金屬基復合材料的研究進展[J];熱加工工藝;2012年02期

10 李燦民;王文芳;吳玉程;;機械合金化制備銅碳合金增強銅-石墨復合材料[J];稀有金屬與硬質合金;2011年04期

相關博士學位論文 前1條

1 楊旭東;均勻分散的碳納米管增強鋁基復合材料的制備與性能[D];天津大學;2012年

，

本文編號：1835722