本文選題：聚氯乙烯涂層膜結構材料　切入點：機織物　出處：《紡織學報》2017年10期

【摘要】：為進一步研究膜結構材料的力學特性,以機織聚氯乙烯涂層膜結構材料為研究對象,對其無損及單邊切口試樣的短期拉伸蠕變性能進行測試,分析切口尺寸及蠕變應力對蠕變性能的影響,并對其拉伸蠕變特性進行研究。實驗結果表明:無損及切口試樣的蠕變曲線均體現了初始蠕變和等速蠕變階段的特征。在同等凈切口蠕變應力條件下,切口試樣的蠕變量小于無損試樣,且隨著切口尺寸的增加而降低。相對于Findley模型,4元件Burger模型較適合描述聚氯乙烯涂層膜結構材料的短期蠕變行為。同時,基于4元件Burger模型擬合系數,分析了蠕變應力及切口尺寸對初始蠕變應變、緩彈性變形和黏性變形的影響。
[Abstract]:In order to further study the mechanical properties of membrane structure materials, the creep properties of non-destructive and one-sided notch specimens were tested with woven polyvinyl chloride coated membrane structure material as the research object. The influence of notch size and creep stress on creep performance is analyzed. The experimental results show that the creep curves of both nondestructive and notched specimens reflect the characteristics of initial creep and constant creep. Under the condition of the same net notch creep stress, The creep amount of notch specimen is smaller than that of non-destructive specimen, and decreases with the increase of notch size. Compared with Findley model, Burger model with 4 elements is more suitable to describe the short-term creep behavior of PVC coated membrane materials. The effects of creep stress and notch size on the initial creep strain, slow elastic deformation and viscous deformation are analyzed based on the fitting coefficients of the four-element Burger model.
【作者單位】： 湖南工程學院紡織服裝學院;湖南省新型纖維面料及加工工程技術研究中心;
【基金】：湖南省科技廳科學研究項目(2013FJ3091)
【分類號】：TB302.3

【相似文獻】

相關期刊論文 前4條

1 徐旭東,關富玲,陳春來;葉片形膜結構的找形[J];工程設計;2001年03期

2 劉雍;馬敬安;;紡織膜結構材料及其發展趨勢綜述[J];天津紡織科技;2006年01期

3 黃春濤;尉洪利;;高海拔地區、強紫外線、強日照環境下膜結構材料比選[J];中華民居(下旬刊);2013年11期

4 陸建剛;花愛春;劉士鑫;劉聰;樊t，

本文編號：1673863