本文關鍵詞： 系統設計 影響因素模擬 擠出成型效果 系統控制　出處：《華中科技大學》2015年碩士論文　論文類型：學位論文

【摘要】：PAM(pressure assisted micro-syringe)氣動式助推微注射器)自由成型技術是一種新型的3D打印技術,在復合生物材料支架制造上具有獨特的優勢。本文旨在對該系統氣動打印技術進行研究,通過設計有效的打印回路,探索系統擠出成型規律;并通過使用軟件模擬,研究成型過程中壓強值,長徑比以及材料粘度對成型效果的影響,并通過實際實驗來進一步分析影響因素的作用并與模擬結論相驗證與補充,從而探索出適合PAM技術的打印工藝,并應用于實際制造;最后本文對系統控制進行初步探索,設計了簡單的系統控制程序。氣動系統的設計決定了氣動擠出時系統的穩定性與效率。本文通過對兩種設計方案的比較,得出了合適的系統設計,同時驗證了負壓的設計效果,并根據設計討論了流量值在擠出過程中對系統輸出效果的影響。壓強P,材料粘度m與針管的長徑比dl影響擠出過程中材料的擠出性能。本文通過運用軟件模擬擠出過程揭示了上述因素在打印過程中對材料擠出效果的影響,并針對各項因素進行了分析。材料在擠出后一個重要性能參數為擠出直徑,直徑大小直接影響到成型支架的生物性能。本文通過控制打印過程中的材料濃度與壓強值,探索了材料成型過程中二者對成型效果的影響,并與模擬分析的結果相驗證,得出了適宜材料成型的工藝參數。
[Abstract]:PAM(pressure assisted micro-syringe pneumatic booster microsyringe) is a new type of 3D printing technology, which has unique advantages in the manufacture of composite biomaterial scaffolds. The purpose of this paper is to study the pneumatic printing technology of this system. By designing an effective printing loop to explore the extrusion rules of the system, and by using software simulation, the influence of pressure, aspect ratio and material viscosity on the forming effect is studied. And through the actual experiment to further analyze the effect of the factors and verify and supplement with the simulation conclusion, so as to explore the printing process suitable for PAM technology, and apply it to the actual manufacturing. Finally, this paper makes a preliminary exploration on the system control. A simple system control program is designed. The design of pneumatic system determines the stability and efficiency of the system during pneumatic extrusion. By comparing the two design schemes, a suitable system design is obtained, and the design effect of negative pressure is verified. According to the design, the influence of flow value on the output effect of the system is discussed. Pressure P, material viscosity m and the ratio of length to diameter of needle tube affect the extrusion performance of the material during extrusion. In this paper, the extrusion performance is simulated by software. The process reveals the influence of the above factors on the extrusion effect of the material during the printing process. After extrusion, an important property parameter is extrusion diameter, which directly affects the biological properties of the molding scaffold. In this paper, the material concentration and pressure in the printing process are controlled. The influence of the two factors on the forming effect was explored, and the results of simulation and analysis were verified, and the suitable process parameters were obtained.
【學位授予單位】：華中科技大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TP391.73;TB30

【相似文獻】

相關期刊論文 前3條

1 胡乾午;楊泰平;李鵬;曾曉雁;;金屬件的激光自由成型制造及影響因素研究[J];激光技術;2007年04期

2 黃棟;;自由成型技術在鏡片制造中的應用[J];中國眼鏡科技雜志;2010年03期

3 ;[J];;年期

相關會議論文 前1條

1 莊建雄;;二氧化碳?xì)怏w保護單面焊雙面自由成型工藝[A];第十屆全國內河船舶與航運技術學術會議論文集[C];2006年

相關碩士學位論文 前1條

1 徐言林;基于PAM自由成型的多噴頭系統氣動打印規律研究[D];華中科技大學;2015年

，

本文編號：1518178