【摘要】：轉向系統輸出角速度的穩定性對汽車操縱的穩定性起到?jīng)Q定性的作用,轉向系統中的雙十字軸萬向節輸入、輸出軸是否能夠等速轉動對轉向系統輸出角速度的穩定性有很大影響.本文論述了使用雙十字軸萬向節時,令靠近輸入端的第一對十字軸萬向節垂直布置,靠近輸出端的第二對十字軸萬向節平行布置,輸入軸和中間軸的夾角等于中間軸和輸出軸的夾角,能實現轉向系統的雙十字軸萬向節等速轉動,并應用該結論對某已有車型的轉向系統進行了改進和優化分析.
[Abstract]:The stability of the output angular velocity of the steering system plays a decisive role in the stability of the vehicle control, and the input of the double cross shaft universal joint in the steering system, Whether the output shaft can rotate at the same speed has a great influence on the stability of the output angular velocity of the steering system. This paper discusses the vertical arrangement of the first pair of cross shaft universal joints near the input end and the parallel arrangement of the second pair of cross shaft universal joints near the output when using the double cross shaft universal joint. The angle between the input shaft and the intermediate shaft is equal to the angle between the intermediate shaft and the output shaft, which can realize the constant speed rotation of the double cross shaft universal joint of the steering system. This conclusion is applied to improve and optimize the steering system of a certain existing vehicle model.
【作者單位】： 廣西科技大學機械工程學院;廣西科技大學工程訓練中心;
【基金】：廣西高等學校優秀人才資助計劃項目(桂教人[2011]40號) 廣西自然科學基金項目(2013GXNSFAA019319) 廣西科技計劃項目(桂科攻1348005-12) 廣西重點實驗室建設項目(13-051-38) 廣西研究生教育創新計劃項目(2013105940802M01)資助
【分類號】：U463.4

【相似文獻】

相關期刊論文 前10條

1 胡烽;趙燕;;電動轉向系統技術研究現狀與展望[J];機械工程師;2006年02期

2 王東升;;轉向系統的三世人生[J];汽車觀察;2007年03期

3 苗政;周偉東;邵宏亮;;車輛機械轉向系統的使用與維護[J];農業與技術;2009年02期

4 竺叢勝;;專于內,精于細 訪武漢捷隆汽車電動轉向系統有限公司總經理姚利軍[J];汽車與配件;2009年50期

5 王磊;魏占芳;沈阿榮;譚俊良;;基于ANSYS Workbench對某越重型野車轉向系統的有限元分析[J];汽車實用技術;2010年01期

6 譚淼;王雷;王暉;閆立濱;;轉向系統前期預測及優化方法[J];汽車實用技術;2013年09期

7 楊，

本文編號：2312562