【摘要】：為了整體提高軸流泵的水力優化設計水平,找出影響軸流泵性能的主要幾何參數,運用正交試驗方法,以揚程、效率、軸功率和壓力脈動作為試驗評判指標,將綜合頻率分析法應用到軸流泵多目標優化設計中�；贚_9(3~4)正交表得到了9組方案,研究葉片數、翼型、輪轂比和葉片與導葉間距離對軸流泵的揚程、效率、軸功率和壓力脈動的影響規律,并通過綜合頻率分析法確定了一組最佳試驗方案。結果表明:該最佳試驗方案在設計流量下,水流在葉輪及導葉段中的流態較好,水流流線順暢,分布相對均勻;軸流泵模型在流量和揚程滿足改型要求的同時,效率提高了5.7%;軸功率下降了1.21%;壓力脈動系數降低了11%,驗證了綜合頻率分析法在多目標正交優化中的可行性。
[Abstract]:In order to improve the hydraulic optimum design level of axial flow pump as a whole and find out the main geometric parameters that affect the performance of axial flow pump, the orthogonal test method is used to evaluate the performance of axial flow pump with lift, efficiency, shaft power and pressure pulsation. The synthetic frequency analysis method is applied to the multi-objective optimization design of axial flow pump. Nine groups of schemes were obtained on the basis of LSP 9 (3 / 4) orthogonal table. The effects of blade number, airfoil, wheel hub ratio and distance between blade and guide vane on the lift, efficiency, shaft power and pressure pulsation of the axial flow pump were studied. A group of optimal test schemes were determined by comprehensive frequency analysis method. The results show that the flow pattern in the impeller and guide vane is better, the flow line is smooth and the distribution is relatively uniform, and the axial flow pump model meets the requirements of the modification of the flow rate and the head at the same time as the flow rate and the head meet the requirements of modification. The efficiency is increased by 5.7, the axial power is reduced by 1.21, and the pressure fluctuation coefficient is reduced by 11, which verifies the feasibility of the comprehensive frequency analysis method in the multi-objective orthogonal optimization.
【作者單位】： 河海大學水資源高效利用與工程安全國家工程研究中心;河海大學水利水電學院;河海大學能源與電氣學院;江蘇省江都水利工程管理處;
【基金】：國家自然科學基金重點項目(51339005)、國家自然科學基金面上項目(51579080) 安徽省自然科學基金面上項目(1608085ME119)
【分類號】：TH312

【相似文獻】

相關期刊論文 前10條

1 沈自強,張建國,孫玉蘭,李明定;軸承套圈內孔精磨精度的正交試驗[J];軸承;1979年05期

2 舒亞海;楊春鵬;;基于正交試驗和有限元計算的優化設計方法[J];雷達與對抗;2014年02期

3 關炎芳;張國賢;金健;;基于仿真和正交試驗的鋸齒形流道結構優化[J];上海大學學報(自然科學版);2009年04期

4 王國新;寧汝新;王愛民;;基于仿真和正交試驗的優化調度研究[J];中國機械工程;2007年20期

5 袁壽其;張金鳳;袁建平;付躍登;;用正交試驗研究分流葉片主要參數對性能影響[J];排灌機械;2008年02期

6 翟穎妮;孫樹棟;王軍強;王萌;;基于正交試驗的作業車間瓶頸識別方法[J];計算機集成制造系統;2010年09期

7 ;y型噴嘴結構優選正交試驗[J];熱力發電;1975年07期

8 邱清盈,馮培恩;基于正交試驗的靈敏度分析法[J];機械設計;1997年05期

9 堯軍平,肖柯則;鈮釩球鐵軋輥材質的試驗[J];鑄造;1998年11期

10 高雄發;施衛東;張德勝;張啟華;方波;;基于CFD正交試驗的旋流泵優化設計與試驗[J];農業機械學報;2014年05期

，

本文編號：2279700