【摘要】：不完全齒輪常采用停止位時從動輪齒形對稱分布,同時降低主動輪首末齒齒高的方法進行設計。為避免重合度小于1,這種方法需要的主從動齒輪全齒數較多。提出了停止位時從動輪齒形非對稱布置的設計方法,推導了設計計算公式,畫出了首對齒與第二對齒的重合度分布圖、始嚙和脫嚙位置的角加速度圖。通過分析表明,選擇標準齒高兩齒輪齒頂?shù)膰С鰠^(qū)交點作脫齒定位點,可保證嚙入和嚙出剛性沖擊較小,并使機構完全避免產生二次沖擊。鎖止弧位置靈活,使從動輪鎖止弧弧長不再受限于首末齒驅動轉過的齒數K值,可用作主從動輪的全齒數可以比較少,結構更加緊湊;主動輪末齒齒頂高不必降低,從動輪可采用全齒輪。
[Abstract]:Incomplete gears are usually designed by symmetrical distribution from the tooth profile of the drive wheel when stopping, and by reducing the height of the front and end teeth of the active gear at the same time. In order to avoid the coincidence degree less than 1, this method needs more total teeth of the main follower gear. In this paper, the design method of asymmetrical arrangement of the tooth form of the motor wheel when stopping position is put forward, the design calculation formula is derived, the distribution diagram of the coincidence between the first pair of teeth and the second pair of teeth, and the angular acceleration diagram of the position of the first pair of teeth and the second pair of teeth are drawn. It is shown by analysis that selecting the intersection point of the gnawing area of the top of two gear teeth with standard tooth height as the position point can ensure that the rigid impact in and out of the gear can be reduced and the secondary impact can be avoided completely by the mechanism. Because of the flexible position of the locking arc, the length of the locking arc is no longer limited by the number of teeth K of the first and last teeth driven by the first and last teeth, so that the total number of teeth of the main and slave driving wheels can be less, and the structure is more compact, and the top height of the final teeth of the active gear does not need to be reduced. Full gear can be used from the drive wheel.
【作者單位】： 集美大學機械與能源工程學院;福建省永安市林業局;
【基金】：國家自然科學基金資助項目(51575233) 福建省自然科學基金資助項目(2012J01225)
【分類號】：TH132.41

【相似文獻】

相關期刊論文 前10條

1 趙學信;;關于結構對稱件的非對稱結構設計的設想[J];林業機械;1986年06期

2 孔午光;不完全齒輪機構的設計[J];西安交通大學學報;1981年01期

3 沈世德;;內接不完全齒輪機構的運動設計[J];江蘇機械;1982年02期

4 朱邦青;;不完全齒輪機構的改進[J];設備管理與維修;1993年06期

5 劉文艷,胡國清;不完全齒輪機構的高速運用[J];機械;2001年02期

6 董愛軍;不完全齒輪機構中鎖止弧的可靠設計[J];機械設計與研究;2002年03期

7 官開才;不完全齒輪機構的緩沖裝置[J];機床;1991年12期

8 劉金武;消除不完全齒輪機構卡死和竄動的對策[J];機械工藝師;1994年12期

9 陳安岳;介紹一種簡易的不完全齒輪機構[J];機械研究與應用;1996年04期

10 余新英;;新穎的主軸瓦緊固機——不完全齒輪機構的應用[J];中國紡織大學學報;1991年Z1期

，

本文編號：2213130