本文選題：核電站用泵 + 軸封式核主泵�。� 參考：《水泵技術》2017年02期

【摘要】：軸封型核主泵是核電站一回路系統中唯一的旋轉設備,屬于高溫、高壓、受核輻照的壓力邊界一級設備。由于系統壓力大,轉子系統所承受的軸向載荷也大,軸向載荷能否精確確定影響轉子各個零部件的設計分析和設計開發,油潤滑推力軸承提供很重要的設計技術參數。本文通過舉例,根據核主泵在電站系統中運行期間的載荷變化,計算核主泵轉子軸向力,并在水力模型裝置上設置力傳感器,驗證計算方法的正確性。
[Abstract]:The shaft seal nuclear main pump is the only rotating equipment in the primary circuit system of nuclear power station. It belongs to the pressure boundary primary equipment of high temperature, high pressure and nuclear irradiation. Because of the high pressure of the system, the axial load on the rotor system is also large. Whether the axial load can accurately determine the design, analysis and development of the parts and components of the rotor, the oil-lubricated thrust bearing provides very important design technical parameters. In this paper, the axial force of the rotor of the nuclear main pump is calculated according to the load variation during the operation of the nuclear main pump in the power station system by an example, and the force sensor is installed on the hydraulic model device to verify the correctness of the calculation method.
【作者單位】： 哈爾濱電氣動力裝備有限公司;
【分類號】：TH38;TM623

【相似文獻】

相關期刊論文 前9條

1 ;SB709主泵試驗器[J];燃?xì)鉁u輪試驗與研究;1999年04期

2 張明乾;劉昱;李承亮;;淺談壓水堆核電站AP1000屏蔽式電動主泵[J];水泵技術;2008年04期

3 賈瑞清,夏志新;AM500采煤機主泵失效機理的研究[J];液壓氣動與密封;1996年01期

4 陳捷;巴基斯坦恰希瑪核電站主泵軸密封[J];水泵技術;2003年01期

5 ;世界首臺第三代核電AP1000主泵試驗進展情況[J];水泵技術;2010年04期

6 張健民;進口起重機主泵改用國產泵[J];工程機械與維修;2000年01期

7 洪振e，

本文編號：2081958