本文選題：雙粗糙模型 + 單粗糙模型　； 參考：《潤滑與密封》2017年11期

【摘要】：基于統計學方法,Greenwood和Tripp(GT模型)提出雙粗糙平面法向接觸(雙粗模型)可以等效為單粗糙平面與剛性平板之間的接觸(單粗模型),但這種等效處理缺乏對接觸應力場分析以及材料硬化的考慮。為進一步研究GT模型,基于高斯粗糙表面數字化表征,通過控制自相關長度和濾波方法,得到雙粗糙平面及其等效單粗糙平面;借助有限元軟件ABAQUS對2組模型法向接觸進行建模及分析。結果表明:2組模型預測的接觸剛度和接觸面積符合較好,但接觸壓力與接觸面積關系存在差異;2組模型預測的等效應力和接觸壓強的應力幅值以及云圖的分布區域大致相近,但雙粗模型由于存在大量微凸體側接觸,弱化接觸狀態以及材料硬化,因而應力幅值偏低。
[Abstract]:Based on the statistical methods of Greenwood and Tripp(GT models, it is proposed that the double rough plane normal contact (double rough model) can be equivalent to the contact between a single rough plane and a rigid plate (a single rough model), but this equivalent treatment lacks the contact stress. Field analysis and consideration of material hardening. In order to further study the GT model, based on the digital representation of Gao Si rough surface, the double rough plane and its equivalent single rough plane are obtained by controlling the autocorrelation length and filtering method. Two groups of normal contact models were modeled and analyzed by finite element software ABAQUS. The results show that the contact stiffness and contact area predicted by the two groups of models are in good agreement, but the relationship between contact pressure and contact area is different. The stress amplitude of equivalent stress and contact pressure predicted by two groups of models and the distribution region of cloud map are approximately similar. However, due to the existence of a large number of micro-convex body side contact, weakening contact state and material hardening, the stress amplitude of the double coarse model is low.
【作者單位】： 上海交通大學機械與動力工程學院;
【基金】：國家自然科學基金項目(11572192)
【分類號】：TH117

【相似文獻】

相關期刊論文 前2條

1 郭磊;陸長德;初建杰;;提高FDM模型表面質量的方法[J];現代制造工程;2006年03期

2 王衛辰;朱真才;方亮;邢邦圣;王繁生;;基于3D CAD模型表面Z向特征曲線的自適應分層方法[J];機械科學與技術;2010年05期

相關碩士學位論文 前2條

1 傅馳林;3D打印節材優化相關技術研究[D];華僑大學;2016年

2 劉溪;虛擬油泥模型表面優化提取及STL模型輸出接口設計[D];西北工業大學;2007年

，

本文編號：1922541