本文選題：智能制造 + 網絡安全��； 參考：《西華大學》2017年碩士論文

【摘要】：《中國制造2025》和《智能制造發展規劃(2016-2020)》的相繼發布,加快了我國智能制造的規劃和布局,以全力搶占先進制造業發展的制高點。隨著信息化和工業化的不斷深度融合,工業互聯網開放程度越來越高,這也向網絡信息安全提出了嚴峻的挑戰,如何解決智能制造中網絡信息安全問題變得迫在眉睫。本論文針對智能制造車間級網絡,分析并設計了網絡安全方案和數據加密方式。在此基礎上,首先完成了系統硬件平臺的電路設計。電路設計包括系統電源ADP5050、FPGA參考時鐘和參考電源、JTAG配置、DDR3存儲K4B2G1646C、千兆以太網KSZ9031MNX、以太網連接器RJ45等模塊。在網絡安全和密碼及編碼學的研究基礎上,采用自頂而下的設計思想完成了系統的軟件設計。軟件設計分為兩部分,一部分接口FPGA,另一部分為算法FPGA。接口FPGA軟件設計主要包含千兆以太網PHY配置,UDP協議、IP協議、ARP協議、DDR3的轉換控制及UniPHY IP配置、數據收發等模塊;算法FPGA軟件設計主要包含數據的輸入寄存和校驗、AES密鑰擴展、AES加解及解密算法、SM4密鑰擴展、SM4加解及解密算法和SM3算法等模塊。在設計過程中分析了FPGA的片上資源及Verilog編碼效率。完成了系統仿真。利用Modsim完成了各子模塊和系統整體的RTL級仿真,并對仿真結果進行了分析和判斷。最后設計了系統的測試方案,并完成了系統的子模塊和整體測試。子模塊測試主要利用QuartusII的Signal Tap II嵌入式邏輯分析儀獲取FPGA的片內的待測信號,而整體測試主要利用Wireshark和網絡調試助手來獲取UDP加密和解密包。子模塊和整體測試均包含了功能、性能和穩定性三個方面,并對測試結果做出了分析和判斷。實驗結果表明,本文設計的車間級網絡方案實現了網絡數據的機密性和認證功能,為智能制造網絡信息安全研究提供了良好的基礎研究。
[Abstract]:The release of "made in China 2025" and "Intelligent Manufacturing Development Plan 2016-2020" one after another has accelerated the planning and layout of intelligent manufacturing in China, in order to seize the commanding point of the development of advanced manufacturing industry. With the continuous integration of information and industrialization, the opening degree of the industrial Internet is becoming more and more high, which also poses a severe challenge to network information security. How to solve the problem of network information security in intelligent manufacturing becomes urgent. In this paper, the network security scheme and data encryption method are analyzed and designed for intelligent manufacturing shop level network. On this basis, the circuit design of the system hardware platform is first completed. The circuit design includes ADP5050 FPGA reference clock and JTAG configuration DDR3 storage K4B2G1646C, Gigabit Ethernet KSZ9031MNXand Ethernet connector RJ45. Based on the research of network security and cryptography and coding, the software design of the system is completed by using the top-down design idea. The software design is divided into two parts, one is the interface FPGA, the other is the algorithm FPGA. The design of interface FPGA software mainly includes the conversion control, UniPHY IP configuration, data transceiver and so on of Gigabit Ethernet PHY configuration, IP protocol, IP protocol and DDR3. The algorithm FPGA software design mainly includes the data input register and the verification AES key extension AES encryption and decryption algorithm SM4 key extension SM4 encryption and decryption algorithm and SM3 algorithm and so on. In the process of design, the on-chip resource and Verilog coding efficiency of FPGA are analyzed. The system simulation is completed. The RTL level simulation of each sub-module and the whole system is completed by using Modsim, and the simulation results are analyzed and judged. Finally, the test scheme of the system is designed, and the sub-module and the whole test of the system are completed. The sub-module test mainly uses QuartusII's Signal Tap II embedded logic analyzer to obtain the on-chip test signal of FPGA, while the whole test mainly uses Wireshark and network debugging assistant to obtain UDP encryption and decryption packet. The sub-module and the whole test include three aspects: function, performance and stability, and the test results are analyzed and judged. The experimental results show that the network scheme designed in this paper realizes the confidentiality and authentication of network data, and provides a good foundation for the research of intelligent manufacturing network information security.
【學位授予單位】：西華大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TH18

【參考文獻】

相關期刊論文 前8條

1 ;智能制造發展規劃(2016-2020年)[J];中國儀器儀表;2017年01期

2 鄭長征;;統籌兼顧,加快推進企業智能制造建設[J];中國工業評論;2016年11期

3 周�？�;;面向智能制造的工業信息安全標準化研究[J];信息技術與標準化;2016年08期

4 蘭昆;唐林;;智能制造信息安全保障體系分析[J];通信技術;2016年04期

5 許鳳凱;;智能制造工業控制系統全生命周期信息安全保障[J];自動化博覽;2016年01期

6 張建軍;程鵬;;智能化工業控制系統的信息安全保障[J];中國工業評論;2015年10期

7 ;工信部啟動2015智能制造試點示范專項行動[J];有色冶金節能;2015年03期

8 何廷潤;;推進“中國制造2025”的網絡信息安全威脅分析[J];移動通信;2015年11期

相關重要報紙文章 前1條

1 左世全;;我國智能制造系統推進全面展開[N];中國電子報;2016年

相關碩士學位論文 前3條

1 王金環;工業控制系統中現場數據傳輸?shù)陌踩匝芯縖D];遼寧工業大學;2015年

2 高永亮;基于SMS4算法的標簽基帶設計與實現[D];西安電子科技大學;2014年

3 蘇振宇;基于FPGA和DSP的PCI-E高速密碼卡設計與實現[D];山東大學;2012年

，

本文編號：1845238