本文選題：幾何收斂點　切入點：泄漏率　出處：《摩擦學學報》2017年05期

【摘要】：采用解析法和數值計算相結合的方法,解釋橢圓微孔端面機械密封的方向角所引起的幾何特性改變?nèi)绾斡绊懙叫孤┞?首先,得到了不同方向角下,橢圓沿速度方向上的幾何收斂點的解析解.然后,基于質量守恒的JFO空化邊界條件建立數值計算模型,分析了液膜的壓力分布,并使用最高壓力點的坐標來近似表征高壓區的位置,得到了方向角與最高壓力點的關系.接著,通過對比,發現幾何收斂點和最大壓力點位置一致,并分析了原因.最后,分析了在不同結構參數和操作參數下方向角對泄漏率的影響規律,通過分析得到,方向角的改變,使幾何收斂點的位置發生改變,從而改變高低壓區的分布,當高壓區靠近泄漏出口時,泄漏率大;當高壓區遠離泄漏出口時,泄漏率小.
[Abstract]:The method of combining analytical method with numerical calculation is used to explain how the change of geometric characteristics caused by the direction angle of the mechanical seal with elliptical microholes affects the leakage rate.Firstly, the analytic solution of the geometric convergence point of the ellipse along the velocity direction is obtained at different direction angles.Then, based on the JFO cavitation boundary condition of mass conservation, the numerical model is established, and the pressure distribution of the liquid film is analyzed. The position of the high pressure region is approximately represented by the coordinates of the highest pressure point, and the relationship between the direction angle and the maximum pressure point is obtained.Then, it is found that the position of the geometric convergence point and the maximum pressure point are the same, and the reason is analyzed.Finally, the influence of directional angle on leakage rate under different structure parameters and operation parameters is analyzed. By analyzing the change of directional angle, the position of geometric convergence point is changed, and the distribution of high and low pressure region is changed.When the high pressure area is near the leakage outlet, the leakage rate is large, and when the high pressure area is away from the leakage outlet, the leakage rate is small.
【作者單位】： 四川大學化學工程學院;
【分類號】：TH136

【相似文獻】

相關期刊論文 前4條

1 辛復聚;;平面應力狀態下主應力與主方向角的對應關系[J];青島化工學院學報;1989年02期

2 付方元;;橢圓儀[J];機械設計;1987年03期

3 廖林清;藺朝莉;屈翔;謝明;;影響V帶當量摩擦因數的摩擦力方向角研究[J];機械傳動;2011年11期

4 瞿雷;陳余平;張建峰;金穎;屈運動;;全息譜轉頻橢圓特征參數的改進及應用[J];蘭州理工大學學報;2014年02期

，

本文編號：1704610