本文選題：進給軸 + 液壓鎖緊軸套　； 參考：《機械設計與制造》2017年12期

【摘要】：液壓鎖緊軸套是五軸聯動機床的關鍵部件,能夠在壓力載荷作用下發生較大的彈性變形,鎖緊進給軸的轉動自由度,對機床定位鎖緊和加工精度有重要的影響,鎖緊扭矩是液壓鎖緊軸套設計的重要參數。為研究軸套內工作表面在加工過程中產生的夾緊誤差對液壓鎖緊軸套鎖緊進給軸時產生的鎖緊扭矩的影響,首先用有限元方法分別計算了液壓鎖緊軸套考慮夾緊誤差和不考慮夾緊誤差工作時產生的鎖緊扭矩;然后在自主設計的實驗臺上進行鎖緊扭矩測試實驗;最后用實驗數據對有限元方法計算數據進行驗證。驗證結果說明,有限元方法計算得到的理論數據相對實驗數據曲線走勢一致,由夾緊誤差引起軸套內工作表面的不同形狀直接影響鎖緊扭矩。
[Abstract]:The hydraulic locking shaft sleeve is the key component of the five-axis linkage machine tool. It can produce large elastic deformation under the pressure load, and the rotational degree of freedom of the locking feed shaft has an important influence on the positioning locking and machining accuracy of the machine tool. Locking torque is an important parameter in the design of hydraulic lock sleeve. In order to study the influence of clamping error caused by the working surface of the inner working surface of the shaft sleeve on the locking torque of the hydraulic lock shaft sleeve when the feed shaft is locked, the clamping error caused by the clamping error of the inner working surface of the shaft sleeve is studied. Firstly, the locking torque produced by hydraulic locking shaft sleeve considering clamping error and not considering clamping error is calculated by using finite element method, and then the locking torque test experiment is carried out on the self-designed test bench. Finally, the finite element method is used to verify the calculation data. The results show that the theoretical data obtained by the finite element method are consistent with the experimental data, and the different shapes of the working surface of the sleeve caused by the clamping error directly affect the locking torque.
【作者單位】： 沈陽工業大學機械工程學院;
【基金】：沈陽市工業科技攻關項目(F12-069-2-00)
【分類號】：TH137.5

【相似文獻】

相關期刊論文 前10條

1 趙存友;礦用液壓鎖技術現狀[J];煤礦機械;2002年09期

2 王佃武;;液壓鎖的常見問題及排除方法[J];機電產品開發與創新;2013年03期

3 王廣懷,劉海之;一種新型液壓鎖閥的研制[J];機床與液壓;2000年03期

4 林國湘,陳從桂;液壓鎖緊系統的模糊可靠性設計[J];煤礦機械;2000年09期

5 張紅軍,魏永辰,馬占才;雙向液壓鎖引出的系統故障[J];液壓與氣動;2000年03期

6 屈福政,費燁;雙向液壓鎖動態特性的研究[J];機床與液壓;2001年01期

7 李光,劉忠,楊國平,楊務滋;一種新型的預節流雙向液壓鎖[J];液壓與氣動;2001年05期

8 劉忠,楊國平,朱浩,楊務滋;一種新型預節流雙向液壓鎖[J];機械工程師;2001年01期

9 王偉;使用液壓鎖應注意的問題[J];機床與液壓;2004年04期

10 鄒建華;吳榕;;液壓鎖技術現狀分析[J];機械工程與自動化;2007年05期

，

本文編號：2073699