本文選題：閉環氣流磨 + 氫化鈦粉��； 參考：《粉末冶金材料科學與工程》2017年04期

【摘要】：隨著鈦及鈦合金粉末冶金技術的快速發展,采用氫化鈦粉代替鈦粉作為主要原料制備粉末冶金鈦材料已成為國內外的研究熱點。本文研究了閉環氣流磨系統粉碎氫化鈦的工藝過程及特點,并采用SEM、化學分析以及激光粒度測試分析等表征所制備氧化鈦粉的形貌、氧含量及粒度分布。結果表明:氫化鈦經閉環氣流磨后,粒度(D_(50))達到5.94μm;不同粒徑(粉末粒徑分別為250,150,75和48μm)的氫化鈦粉在閉環氣流磨分級輪頻率為200Hz下,粒度(D_(50))達到10μm以內,且粒度分布區間較窄;而同一粒徑(250μm)的粉末在閉環氣流磨不同分級輪頻率下(80,100,120,140,160,180和200 Hz)分級后,粉末的粒度(D_(50))和粒度分布區間隨分級輪頻率的降低而增大和變寬;因?yàn)殚]環氣流磨系統是封閉的循環回路,采用高純氬氣作為磨料介質,因此物料粉碎前后的增氧量低。
[Abstract]:With the rapid development of titanium and titanium alloy powder metallurgy technology, the preparation of powder metallurgy titanium materials using titanium hydride instead of titanium powder as the main raw material has become a hot spot at home and abroad. In this paper, the technological process and characteristics of the closed-loop airflow mill system for grinding titanium hydride were studied. The morphology, oxygen content and particle size distribution of the prepared titanium oxide powder were characterized by SEM, chemical analysis and laser particle size measurement. The results showed that the particle size of titanium hydride was 5.94 渭 m after closed-loop airflow milling, and the particle size of titanium hydride powder with different particle sizes (250150 渭 m and 48 渭 m respectively) was less than 10 渭 m and the particle size distribution was narrower than 10 渭 m when the frequency of closed-loop airflow mill classifier wheel was 200Hz, and the particle size distribution of titanium hydride was less than 10 渭 m. However, the powder with the same particle size (250 渭 m) and the particle size distribution increased and widened with the decrease of the frequency of the wheel, and the particle size and distribution range of the powder were increased and widened with the decrease of the frequency of the classifying wheel after the powder was classified by 80100120140160180 and 200Hz) under the different frequency of the closed-loop airmill, the particle size of the powder increased with the decrease of the frequency of the wheel. Because the closed-loop airflow mill system is a closed loop with high purity argon as abrasive medium, the increase of oxygen is low before and after comminution.
【作者單位】： 成都理工大學材料與化學化工學院;攀枝花學院;
【基金】：國家自然科學基金資助項目(51174122) 四川釩鈦產業技術研究院項目(2013GC0146) 攀枝花科技局項目(2014CY-G-5)
【分類號】：TF123.23

【相似文獻】

相關期刊論文 前5條

1 張晗亮;張健;李增峰;黃瑜;;氫化法制備不飽和氫化鈦粉末[J];稀有金屬;2006年S2期

2 羅錫山;氫化鈦直接反應合成氮化鈦的研究[J];粉末冶金工業;1997年03期

3 劉福平;陳平;楊凱珍;;氫化鈦粉脫氫過程伴隨脫氮行為的熱力學分析[J];粉末冶金工業;2009年06期

4 劉志堅，，曲選輝，黃伯云;氫化鈦－鋁混合粉機械合金化研究[J];中南工業大學學報;1995年02期

5 洪艷;曲濤;沈化森;王兆林;車小奎;;氫化脫氫法制備鈦粉工藝研究[J];稀有金屬;2007年03期

相關博士學位論文 前2條

1 葉青;凝膠注模成形鈦合金的研究[D];北京科技大學;2015年

2 李紅梅;生物醫用鈦及鈦合金的粉末冶金制備工藝研究[D];昆明理工大學;2012年

本文編號：1878569