發布時間：2018-05-01 11:19

  本文選題：輥縫儀 + DSP��； 參考：《武漢理工大學》2014年碩士論文

【摘要】：本文的目標是設計一款具有自主知識產權的多功能連鑄機輥縫測量儀。在設計中采用DSP芯片TMS320F28335作為輥縫儀測量系統的處理器，以DSP為核心單元設計外圍硬件電路，在uC/OS-II嵌入式實時操作系統平臺上完成多功能輥縫測量儀的軟件設計，并利用上位機軟件來分析顯示測量數據，數據的傳輸是采用無線的方式實現的。整個系統設計實現了對連鑄機物理參數的測量，通過傳感器采集連鑄機的輥縫值、角度值、導輥旋轉情況、噴嘴噴霧情況等數據，將這些數據進行初步處理后存儲起來，然后通過無線傳輸?shù)姆绞剿徒o上位機，在上位機軟件中再次分析處理后以圖表的方式顯示出來。連鑄機維護人員根據顯示出來的最終結果，判斷出當前被測連鑄機的工況。 文中介紹了連鑄機各個物理參數的測量原理以及系統整體的軟硬件設計方案。硬件設計方案是以DSP為處理器，采用內外部ADC為模數轉換單元，搭載信號調理、電平轉換、顯示、通訊、電源等模塊電路共同組成了輥縫儀測量硬件平臺，分析了各硬件模塊電路的功能，并驗證硬件電路的可行性；軟件設計是硬件為基礎，采用嵌入式系統的方式實現，通過在CCS開發環境中完成了uC/OS-II操作系統的移植工作，采用多任務處理功能實現系統的軟件編程；系統軟件設計完成之后，結合軟硬件測試整個系統功能就顯得很必要，，整個設計的完成需經過了多次測試，前期主要是實驗室測試，并給出一些具體的測試方法，通過實驗室測試之后才能進行現場測試；上位機軟件主要用來顯示測量結果，文中給出了一些測量結果的顯示方式，并簡略說明如何分析這些顯示出來的數據。最后，總結論文的主要工作及其存在的問題，并對未來工作提出了建議和改進的方向，對于輥縫儀的發展也做出了一些探討。 經論證本文設計的多功能輥縫儀設計合理、檢測準確、工作穩定、操作簡單，具有很高的應用價值。
[Abstract]:The goal of this paper is to design a multi-function continuous casting machine roll gap measuring instrument with independent intellectual property. In the design, DSP chip TMS320F28335 is used as the processor of the roll gap measuring system, and the peripheral hardware circuit is designed with DSP as the core unit. The software design of the multifunction roll gap measuring instrument is completed on the uC/OS-II embedded real-time operating system platform. The data of display and display are analyzed by the software of upper computer, and the data transmission is realized by wireless way. The whole system is designed to measure the physical parameters of continuous casting machine. The data of roll gap value, angle value, guide roll rotation, nozzle spray and so on are collected by sensor, and these data are stored after preliminary processing. Then it is sent to the host computer by wireless transmission, and then analyzed and processed again in the software of the host computer, and then displayed in the form of chart. The maintainers of the caster judge the current condition of the CCM according to the final result. This paper introduces the measuring principle of each physical parameter of the continuous casting machine and the whole software and hardware design scheme of the system. The hardware design is based on DSP processor and internal and external ADC as A / D conversion unit. The hardware platform is composed of signal conditioning, level conversion, display, communication, power supply and other modules. The function of each hardware module circuit is analyzed, and the feasibility of the hardware circuit is verified. The software design is based on hardware and is implemented by embedded system. The transplant of uC/OS-II operating system is accomplished in CCS development environment. After the software design of the system is completed, it is necessary to test the whole system function with the software and hardware. The completion of the whole design has to go through many tests, mainly laboratory tests in the early stage. Some specific test methods are also given, which can only be tested in the field after the laboratory test. The host computer software is mainly used to display the measurement results, and some display methods of the measurement results are given in this paper. And briefly explain how to analyze these displayed data. Finally, the paper summarizes the main work and its existing problems, and puts forward some suggestions and improvement directions for future work, and also makes some discussions on the development of the roll gap meter. It is proved that the multifunctional roll gap meter designed in this paper is reasonable in design, accurate in detection, stable in work, simple in operation, and of high application value.
【學位授予單位】：武漢理工大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TF341.6;TP216

【參考文獻】

相關期刊論文 前7條

1 張維勝;傾角傳感器原理和發展[J];傳感器世界;2002年08期

2 萬雅競;房繼虹;林賢聰;林勃浩;;板坯連鑄機輥縫檢測系統[J];工業計量;2003年S1期

3 曾偉;廖力清;;實時操作系統μC/OS-Ⅱ在DSP上移植的實現[J];計算機工程;2007年17期

4 王覃;刁紅敏;;輥縫儀傳感器的設計原理與應用[J];可編程控制器與工廠自動化;2009年02期

5 嵇美華;許冀勝;;輥縫儀的技術演變及應用前景[J];連鑄;1997年02期

6 馬金萍;;淺談輥縫測量儀的原理及校準過程[J];黑龍江冶金;2011年02期

7 許川佩;王偉;戴葵;胡德國;;實時多任務系統μC/OS-Ⅱ在DSP上的移植[J];微計算機信息;2007年35期

本文編號：1829125