本文選題：方位轉臺 + 角接觸球軸承�。� 參考：《火控雷達技術》2015年04期

【摘要】：針對某方位轉臺面對面排列的角接觸球軸承組件和下軸承內外圈需同時定位的結構特點,結合主要承擔軸向載荷的塑料導軌預留0.4mm裝配間隙的要求,分析轉臺的結構工藝性,討論軸承組件的預緊和預緊對基座中心載荷的卸荷作用,探討轉臺的軸向載荷主要由基座和托架形成的塑料導軌承載的措施,通過實踐驗證了預緊量選取和預緊卸荷值計算的正確性,給出了轉臺軸承組件裝配尺寸的控制要求,通過預緊提高了轉臺運轉的均勻性。
[Abstract]:In view of the structural characteristics of the angular contact ball bearing assembly arranged face to face and the inner and outer ring of the lower bearing, which are arranged face to face of a certain azimuth turntable, combined with the requirement of reserved 0.4mm assembly clearance of plastic guideway bearing axial load, the structural and technological properties of the turntable are analyzed. This paper discusses the unloading effect of bearing assembly preload and preload on the center load of the base, and discusses the measures of bearing the plastic guide rail formed mainly by the base and the bracket in the axial load of the turntable. The correctness of the selection of preload and the calculation of unloading value are verified through practice. The control requirements of assembly size of turntable bearing components are given, and the uniformity of turntable operation is improved by pre-tightening.
【作者單位】： 西安電子工程研究所;
【分類號】：TN957

【相似文獻】

相關會議論文 前1條

1 羅義順;;八角墊密封問題探討[A];西部大開發 科教先行與可持續發展——中國科協2000年學術年會文集[C];2000年

相關重要報紙文章 前1條

1 王冀;本田新車Inspire應用多項新安全裝置[N];中國汽車報;2003年

相關碩士學位論文 前1條

1 古海波;全纏繞復合氣瓶預緊壓力和纏繞層厚度的優化[D];大連理工大學;2006年

，

本文編號：1860596