本文關鍵詞：短波通信控制板的軟件設計及單板測試　出處：《西安電子科技大學》2015年碩士論文　論文類型：學位論文

  更多相關文章： 短波通信 通信控制板 以太網口 串口 系統時間 功能測試

【摘要】：本文研究?jī)?nèi)容源自科研課題“短波選頻與建鏈系統技術研究”。本文將從短波選頻與建鏈系統的方案需求出發,設計并實現了短波通信控制板的基本軟件模塊及單板測試方案。作者完成的主要工作和取得的成果如下:(1)短波選頻與建鏈系統主要由用戶終端、短波建鏈控制器和短波信道機組成,短波建鏈控制器中的短波通信控制板負責運行建鏈通信協議。為了保證通信建鏈協議的正常運行,本文設計了短波通信控制板中各個基本模塊的方案。(2)根據基本模塊的設計方案,設計并實現了通信控制板的以下軟件模塊:串行接口模塊、以太網模塊、系統時間模塊、通用定時器模塊、與DAC芯片通信模塊、看門狗模塊、禁止JTAG模塊。短波通信控制板,作為短波選頻與建鏈系統的通信控制器件,采用網口與用戶終端進行通信,通過串口與Modem、北斗模塊、收發信機進行數據交換。在通信控制板的系統內部,運行了定時器模塊,為建鏈通信協議的狀態跳轉提供定時功能。而為了保持通信雙方的時間同步性,采用了冬眠RTC模塊,并通過冬眠RTC模塊在控制板內運行了與世界標準時間同步的系統時間。出于對系統安全性和穩定性的考慮,實現了禁止JTAG功能模塊和看門狗模塊。這些功能模塊都是確保系統協議和控制軟件能正常運行必不可少的部分。(3)設計并實現了通信控制板的單板測試方案。在完成通信控制板的焊接工作之后,為了檢測單板能否正常工作,編寫了PC端用戶測試軟件和通信控制板的單板測試程序,實現了對單板上的串口、以太網口、系統時間、及與外部模塊通信的測試。將基本模塊納入整個控制板程序后,經過測試驗證證明,各個功能模塊都能正常工作,并且能滿足系統的性能需求。同時,對焊接好的控制板進行的單板測試,也說明單板測試滿足設計需求。
[Abstract]:The research content of this paper is derived from the research project "Research on the technology of shortwave frequency selection and chain building system". This paper will proceed from the demand of the scheme of shortwave frequency selection and chain building system. The basic software module and single board test scheme of shortwave communication control board are designed and implemented. The main work and achievements of the author are as follows: 1) the short wave frequency selection and chain building system is mainly by the user terminal. The shortwave communication control board is responsible for running the link building protocol in order to ensure the normal operation of the communication chain building protocol. According to the basic module design scheme, the following software modules of communication control board are designed and implemented: serial interface module, Ethernet module. System time module, general timer module, communication module with DAC chip, watchdog module, forbidden JTAG module. Shortwave communication control board is used as the communication controller of shortwave frequency selection and chain building system. The interface is used to communicate with the user terminal, and the serial port is used to exchange data with Modem, Beidou module and transceiver. In the system of communication control board, the timer module is run. In order to keep the synchronization of communication both sides, the hibernating RTC module is used to provide the timing function for the state jump of the building chain communication protocol. And through hibernating RTC module in the control board to run with the world standard time synchronization system time, out of the system security and stability considerations. The disabling JTAG function module and watchdog module are implemented. These function modules are essential to ensure the normal operation of the system protocol and control software. The single board test scheme of communication control board is designed and implemented. After the welding of communication control board is completed. In order to check whether the single board can work normally, the test software of PC user and the single board test program of communication control board are written. The serial port, Ethernet port and system time on the single board are realized. After the basic module is integrated into the whole control board program, the test proves that each functional module can work normally and can meet the performance requirements of the system. At the same time. The veneer test of the welded control board also shows that the veneer test meets the design requirements.
【學位授予單位】：西安電子科技大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TN925;TP311.52

【相似文獻】

相關期刊論文 前10條

1 馬滿倉;楊杰;;短波通信中的正交頻分復用技術分析及應用[J];軍民兩用技術與產品;2006年10期

2 葛俊峰;呼和滿都拉;;影響短波通信的主要因素[J];集寧師專學報;2007年04期

3 崔海歐;;短波通信損耗分析及通信頻點預測[J];中國電子科學研究院學報;2008年04期

4 王睿;張海勇;楊曦;阮e，

本文編號：1441345