【摘要】：新研發的井下工具必須經嚴格實驗檢驗才能投放現場,因此,實際工況的準確模擬顯得尤為重要。針對固井滑套在壓裂時具有大排量與高含砂比的特點,設計了四泵串并聯方式的工況模擬實驗?zāi)Ｐ�。根�?jù)實驗條件,先假設沖蝕實驗設備連接方案為兩泵并聯方式,而理論計算得出泵為管路所提供的揚程需達到35.82 m,與實測單臺離心泵Q H特性曲線相結合,最終確定了設備連接方案為四泵串并聯方式。通過監測模擬沖蝕實驗中的排量與含砂比,結果表明,所設計的實驗方案能夠滿足模擬大排量(4.5～7.0 m3/min)、高含砂比(體積比25%)的沖蝕要求且存在較大余量;同時得出進行壓裂作業時不同孔眼數的滑套對管路整體壓力損耗、實驗流量、泵送能力等影響明顯。
[Abstract]:The newly developed downhole tools must be strictly tested before they can be put on the spot, so it is particularly important to simulate the actual working conditions accurately. In view of the characteristics of large displacement and high sand content in fracturing, a working condition simulation experimental model of four pumps in series and parallel mode is designed. According to the experimental conditions, it is assumed that the connection scheme of the erosion experimental equipment is the parallel mode of the two pumps, and the theoretical calculation shows that the lift provided by the pump for the pipeline needs to reach 35.82 m, which is combined with the measured Q-H characteristic curve of a single centrifugal pump. Finally, the equipment connection scheme is determined to be a series-parallel mode of four pumps. By monitoring the ratio of displacement to sand content in the simulated erosion experiment, the results show that the designed experimental scheme can meet the simulated large discharge (4.5 m3/min). The erosion requirement of high sand content ratio (volume ratio 25%) is high and there is a large margin. At the same time, it is concluded that the sliding sleeve with different number of holes has obvious influence on the overall pressure loss, experimental flow rate and pumping capacity of the pipeline.
【作者單位】： 西南石油大學機電工程學院;中國石化石油工程技術研究院;
【分類號】：TE931.2

【相似文獻】

相關期刊論文 前10條

1 張世甫;滑套使用中若干問題的分析探討[J];鉆采工藝;2002年01期

2 ;機械式可開關滑套試驗成功[J];石油機械;2013年06期

3 石磊;;一種新型滑套開關工具及配套技術應用研究[J];西南石油大學學報(自然科學版);2014年01期

4 郭朝輝;魏遼;馬蘭榮;;新型無級差套管滑套及其應用[J];石油機械;2012年10期

5 秦金立;戴文潮;萬雪峰;趙晨熙;韓峰;;無線射頻識別技術在多級滑套壓裂工具中的應用探討[J];石油鉆探技術;2013年03期

6 戴文潮;秦金立;薛占峰;侯乃賀;趙晨熙;;一球多簇分段壓裂滑套工具技術研究[J];石油機械;2014年08期

7 汪超;徐建寧;屈文濤;朱端銀;;內滑套式射流泵的研制[J];流體機械;2008年01期

8 李大寨;王克沛;;基于RFID技術的智能滑套分段壓裂工具的設計[J];機械與電子;2014年02期

9 張亮;王丙剛;馬認琦;;深水生產滑套密封設計及試驗[J];石油機械;2014年07期

10 孔春巖;張德榮;張笑非;;水平井可關閉壓裂滑套有限元分析[J];石油礦場機械;2013年05期

相關碩士學位論文 前1條

1 張逸飛;三銷滑套溫冷復合精密鍛擠多工序成形工藝研究[D];山東大學;2016年

，

本文編號：2479047