【摘要】：本文結合J16區塊油藏地質條件及開發條件,研究了聚合物的竄流機理及其影響因素,并在充分利用地下大量殘留聚合物的基礎上,應用油田處理污水常用的凈水劑凈化污水的原理,即陽離子絮凝劑與聚合物可以發生絮凝反應原理,對新型陽離子調堵劑的種類、用量、注入方式、段塞尺寸等進行了研究及優選。靜態實驗結果表明:當聚合物濃度分別為100、500、1000、1500mg/L時,調堵劑1、2、4的最佳理想濃度為0.1%、0.3%、0.5%和1%;聚合物濃度不超過1500mg/L時,所選用的7種陽離子調堵劑中,調堵劑1、2、4的聚沉效果較好。動態實驗結果表明:陽離子調堵劑1、2、4均能在人造巖心中與聚合物發生反應,起到延遲初始見聚時機、降低聚合物峰值濃度、降低聚合物峰值出現時機以及提高初始注聚壓力的作用;且對于相同的堵劑,注入濃度和注入量越大,注入壓差就越大,初始見聚時機就越延后,峰值濃度也越低;但由于聚合物量是一定的,因此當注入的濃度和注入量增大到一定程度后,峰值濃度降低幅度則變小;在巖芯封堵效果實驗中,其封堵率大于96.6%,說明該調堵體系在巖芯中具有較好的耐沖刷性能,建議調堵劑的注入濃度高于0.6%,注入段塞高于0.5PV。
[Abstract]:Based on the reservoir geological conditions and development conditions in block J16, the mechanism of polymer channeling and its influencing factors are studied in this paper, and on the basis of making full use of a large number of residual polymers in the underground, The principle of purifying wastewater by water purification agent commonly used in oilfield treatment is applied, that is, the principle of flocculating reaction between cationic flocculant and polymer, the type, dosage and injection mode of new cationic plugging agent, The size of slug is studied and optimized. The results of static experiment showed that when the concentration of polymer was 100,500,1000,1500 mg / L respectively, the optimum concentration of plugging agent 1,2,4 was 0.1%, 0.3%, 0.5% and 1% respectively, and the optimal concentration was 0.1%, 0.3%, 0.5% and 1%, respectively. When the concentration of polymer is less than 1500mg/L, the concentration of 1, 2 and 4 Cationic plugging agents is better than that of Cationic plugging agent. The results of dynamic experiments show that Cationic plugging agent 1,2,4 can react with polymer in artificial core, delay the initial polymerization time, and reduce the peak concentration of polymer, and the experimental results show that Cationic plugging agent 1, 2, 4 can react with polymer in artificial core. The effect of decreasing the peak time of polymer and increasing the initial pressure of polymer injection; For the same plugging agent, the higher the injection concentration and the amount of injection, the greater the injection pressure difference, the longer the initial polymerization time is, and the lower the peak concentration is. However, because the amount of polymer is certain, when the concentration and amount of injection increase to a certain extent, the decrease of peak concentration becomes smaller. In the experiment of core plugging effect, the plugging efficiency is more than 96.6%, which indicates that the plugging system has better anti-scour performance in the core. It is suggested that the injection concentration of plugging agent is higher than 0.6% and the injection slug is higher than 0.5PV.
【學位授予單位】：東北石油大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TE39
，

本文編號：2446246