本文選題：定轉子 + 接觸非線性�。� 參考：《東北石油大學》2017年碩士論文

【摘要】：定轉子由定子和轉子組成,是井下螺桿泵的核心部件,提高定轉子的工作性能對螺桿泵采油效率的提升有重要意義。定轉子的工作性能受到多種因素的影響,本文通過對定轉子進行線型、溫度場、非均勻流體壓力的理論分析之后,在給定初始過盈量、井溫和溶脹的條件下,施加非均勻流體壓力,建立了定轉子周期性接觸非線性有限元模型,進行定轉子的生熱和非線性接觸的數值模擬分析。對定子橡膠襯套的滯后生熱和摩擦生熱進行比較,證明摩擦生熱可以被忽略。對不同液壓施加情況下的生熱變化和接觸壓力變化進行比較,以及對轉子轉動前是否施加滯后生熱溫度場兩種情況下的接觸壓力進行比較,為更精確的模擬定轉子實際工況提供依據。分析了不同的材料硬度、不同的轉速、不同的損耗因子對定轉子生熱和接觸的影響,材料硬度的增加導致橡膠襯套溫升減小,接觸壓力、等效應力增加;轉速和損耗因子的增加均主要導致橡膠襯套溫升的增加。在實際應用中,可根據實驗測試的定子橡膠溶脹率和實現密封效果的接觸壓力,指導定轉子初始過盈或間隙的設計值。
[Abstract]:Stator and rotor are the core components of screw pump. It is very important to improve the performance of stator and rotor to improve the oil recovery efficiency of screw pump. The working performance of stator and rotor is affected by many factors. After the theoretical analysis of linear, temperature field and non-uniform fluid pressure of stator and rotor, under the condition of given initial interference and well mild swelling, The nonlinear finite element model of periodic contact between stator and rotor is established by applying non-uniform fluid pressure. The heat generation and nonlinear contact of stator and rotor are simulated and analyzed numerically. By comparing the delayed heat generation and friction heat generation of the stator rubber bushing, it is proved that the friction heat generation can be neglected. The heat generation change and contact pressure change under different hydraulic pressure are compared, and the contact pressure is compared under the condition of whether or not the temperature field of hysteresis heat generation is applied before rotor rotation. It provides a basis for more accurate simulation of the actual working conditions of stator and rotor. The influence of different material hardness, different rotation speed and different loss factor on heat generation and contact between stator and rotor is analyzed. The increase of material hardness leads to the decrease of rubber bushing temperature, the contact pressure and the increase of equivalent stress. The increase of rotational speed and loss factor mainly leads to the increase of temperature rise of rubber bushing. In practical application, the design value of initial interference or clearance of stator and rotor can be guided according to the swelling rate of stator rubber and the contact pressure to realize sealing effect.
【學位授予單位】：東北石油大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TE933.3

【參考文獻】

相關期刊論文 前10條

1 薛建泉;張國棟;吳慎渠;谷國劍;李敏慧;;基于ANSYS的螺桿泵內部壓力分布有限元分析[J];潤滑與密封;2012年09期

2 操建平;孟慶昆;高圣平;王向東;胡貴;;螺桿泵定子熱力耦合的計算方法研究[J];力學季刊;2012年02期

3 薛建泉;張國棟;吳慎渠;李敏慧;谷國劍;楊峰;;雙熱源作用下螺桿泵定子非穩態溫度場數值模擬[J];中國石油大學學報(自然科學版);2012年03期

4 安永生;宋揚;張德實;馬露霞;孫春龍;;螺桿泵轉子三維運動仿真分析及型線優化設計[J];中國石油大學學報(自然科學版);2012年03期

5 賀向東;吳恒安;劉合;曹剛;張勁;王秀喜;;基于溫脹和溶脹特性的螺桿泵定子型線設計[J];工程力學;2011年07期

6 吳俊飛;高威;李云鵬;;三頭單螺桿泵定轉子接觸磨損分析[J];潤滑與密封;2011年05期

7 韓國有;趙毅;杜秀華;;采油螺桿泵三維有限元模型分析[J];大慶石油學院學報;2010年05期

8 曹剛;劉合;金紅杰;吳恒安;王秀喜;;螺桿泵動力學熱力耦合分析方法研究[J];計算力學學報;2010年05期

9 金紅杰;吳恒安;曹剛;劉合;王秀喜;;螺桿泵系統漏失和磨損機理研究[J];工程力學;2010年04期

10 劉健;仇性啟;薄萬順;許俊良;;橡膠O形密封圈最大接觸壓力數值分析[J];潤滑與密封;2010年01期

相關博士學位論文 前1條

1 杜秀華;采油螺桿泵螺桿—襯套副力學特性及磨損失效研究[D];大慶石油學院;2010年

，

本文編號：2086521