本文選題：二元驅 + 等流度�。� 參考：《東北石油大學》2015年碩士論文

【摘要】：J16塊試驗區實施二元驅以來,由于地層非均質性的影響,產生部分注入井單層吸液量過大,注入液在各層中的推進速度不一致,相應的采油井聚合物濃度上升較快等問題。因此需要開展二元驅多段塞等流度注入方法研究,通過高滲通道局部截流提高壓力梯度來解決這種矛盾。通過開展不同分子量聚合二元體系不同粘度條件下均質巖心注入實驗,進行等流度段塞設計。實驗結果表明:在相同滲透率條件下,同一分子量聚合物配制二元體系流度與粘度成冪函數關系。通過開展三管并聯巖心注入實驗,進行等流度段塞流度控制能力研究。實驗結果表明:籠統注入方式下,連續降分子量等流度注入方案對分流率控制不如單一高分子量方案好。分層分質注入時,連續降分子量注入方法可達到理想的分流率控制效果。分層分質等流度方案采出程度比單段塞籠統注入方案高出19.11%,采收率提高值主要貢獻于低滲透層。通過開展三層非均質巖心驅油實驗,考察多段塞等流度方法驅油效果。實驗結果表明:選用單一分子量(2500×104)聚合物時,三段塞等流度二元驅油體系采出程度高于常規單段塞驅4.45%。連續將分子量4輪次等流度段塞注入時化學驅采出程度最高為35.2%,高于單段塞方案13.92%。連續降分子量4輪次注入能夠更好的控制含水上升速度,長時間維持較高注入壓力,更大限度增強等流度驅油效果。
[Abstract]:Since the binary flooding was carried out in block J16, due to the influence of formation heterogeneity, some problems such as too large amount of single-layer fluid absorption in some injection wells, inconsistent propelling speed of injection fluid in each layer, and rapid increase of polymer concentration in the corresponding oil wells are also discussed. Therefore, it is necessary to study the method of equal mobility injection for binary flooding with multiple slugs, and to solve this contradiction by increasing pressure gradient by local closure of high permeability channel. The constant mobility slug design was carried out through the experiments of homogeneous core injection under different molecular weight polymerization binary systems and different viscosity conditions. The experimental results show that under the same permeability condition, the mobility and viscosity of binary system prepared by the same molecular weight polymer are power function. Through three parallel core injection experiments, the fluidity control ability of constant mobility slug was studied. The experimental results show that under the general injection mode, the constant mobility injection scheme with continuous molecular weight reduction is not as good as the single high molecular weight scheme in controlling the shunt rate. Continuous molecular weight reduction injection method can achieve ideal shunt rate control effect. The recovery degree of the stratified equal mobility scheme is 19.1111 higher than that of the single slug general injection scheme, and the enhanced oil recovery mainly contributes to the low permeability layer. Through three layers heterogeneous core flooding experiment, the displacement effect of multi-slug equal mobility method was investigated. The experimental results show that the recovery degree of triple-slug iso-mobility binary flooding system is higher than that of conventional single-slug flooding with a single molecular weight (2500 脳 10 ~ 4) polymer. When the molecular weight of 4 rounds of constant mobility slug is continuously injected, the highest recovery degree of chemical flooding is 35.2g, which is higher than that of single slug scheme 13.92. Continuously reducing molecular weight 4 times injection can better control the water cut rising speed, maintain high injection pressure for a long time, and enhance the displacement effect of constant mobility oil to a greater extent.
【學位授予單位】：東北石油大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TE357.46

【參考文獻】

相關期刊論文 前7條

1 韓培慧;趙群;穆爽書;李治平;哈斯.巴特爾;;聚合物驅后進一步提高采收率途徑的研究[J];大慶石油地質與開發;2006年05期

2 李春燕;;二元復合驅與單一聚合物驅動態異同點分析[J];內江科技;2012年02期

3 馬濤;;復合吸水顆粒深部液流轉向劑注入性研究[J];西南石油大學學報(自然科學版);2010年04期

4 吳文祥;張濤;胡錦強;;高濃度聚合物注入時機及段塞組合對驅油效果的影響[J];油田化學;2005年04期

5 孫靈輝;代素娟;吳文祥;;低堿三元復合體系用于聚驅后進一步提高采收率[J];油田化學;2006年01期

6 夏惠芬;王剛;鞠野;劉仁強;諸葛祥龍;;聚合物/羧基甜菜堿二元復合體系驅替水驅后殘余油的機理[J];油田化學;2006年04期

7 高明;宋考平;葉銀珠;姚再學;劉連福;;喇嘛甸油田二類油層高濃度聚合物驅提高采收率實驗研究[J];油田化學;2010年02期

相關碩士學位論文 前1條

1 王志偉;聚驅后等流度平行多段塞提高采收率方法研究[D];中國石油大學;2009年

，

本文編號：2085579