本文選題：電磁兼容　切入點：電磁干擾　出處：《南京郵電大學》2013年碩士論文

【摘要】：在電子產品設備高度發展的今天，，人們對電子設備的工作穩定性等也有了更高的要求。在設計電子設備時，電磁兼容問題不容忽視，良好的電磁兼容性是設備正常運作的保障。如果產品成型之后再發現電磁兼容問題并設法解決，在理論和實際上都將十分困難。所以在產品成型之前如果能很好的解決設備的電磁兼容問題無疑會節省很多時間和精力，因而對電子設備的PCB板即印刷電路板進行電磁兼容分析具有重要的研究意義。 論文首先介紹了PCB板的設計并討論了電路板電磁兼容問題的基本理論，闡述了印刷電路板出現電磁兼容性問題的原因，并進行了理論研究。在南昌路通高新技術有限責任公司參與項目并研究設計出用于收發鐵路信號的嵌入式Modem，給出了設計方法以及系統的軟件組成，并在此基礎上對其進行了PCB板電磁兼容分析。針對PCB板中的電磁兼容問題，論文還創新的使用Mentor Graphics公司的Hyperlynx軟件對該嵌入式Modem進行建模仿真，成功的詳細分析了PCB主要存在的電磁兼容問題，并且針對典型的時鐘晶振網絡干擾和線間串擾這兩大電磁兼容問題提出了合理有效的解決辦法，由此總結提出了一些用于PCB板電磁兼容設計的原則。提出的解決辦法均使用軟件輔助仿真進行驗證，得出了合理正確的結論，并且在公司產品成型實際使用時，達到了預期的效果。
[Abstract]:With the high development of electronic equipment, people have higher requirements for the stability of electronic equipment. When designing electronic equipment, the problem of EMC can not be ignored. Good EMC is the guarantee of the normal operation of the equipment. If the EMC problem is discovered after the product is formed and solved, It will be very difficult both in theory and in practice. So if you can solve the EMC problem of the equipment before the product is formed, it will undoubtedly save a lot of time and effort. Therefore, it is of great significance to analyze the electromagnetic compatibility of the PCB board of electronic equipment, that is, printed circuit board. Firstly, the paper introduces the design of PCB board, discusses the basic theory of EMC of PCB, and explains the reason of EMC problem in PCB. In the project of Nanchang Lutong High-tech Co., Ltd., the embedded Modemon used to receive and receive railway signals is designed and designed. The design method and the software composition of the system are given. On this basis, the electromagnetic compatibility of PCB board is analyzed. Aiming at the problem of EMC in PCB board, the paper also innovatively uses the Hyperlynx software of Mentor Graphics to model and simulate the embedded Modem. The main EMC problems in PCB are analyzed in detail, and a reasonable and effective solution to the two EMC problems, which are typical clock crystal network interference and inter-line crosstalk, is put forward. Some principles used in EMC design of PCB board are summarized and put forward. The proposed solutions are verified by software aided simulation, and a reasonable and correct conclusion is drawn, and when the products are actually used in the company, The expected effect has been achieved.
【學位授予單位】：南京郵電大學
【學位級別】：碩士
【學位授予年份】：2013
【分類號】：TN41;TP368.1

【參考文獻】

相關期刊論文 前4條

1 李莉,李衛兵,王學剛,張謙;二平行傳輸線間的串擾分析[J];電波科學學報;2001年02期

2 張華,洪偉;不完整地參考面對高速互連耦合及串擾的影響分析[J];東南大學學報(自然科學版);2005年05期

3 呂飛燕,沙斐;PCB上串擾的耦合機理和優化分析模型[J];電子與信息學報;2005年07期

4 路宏敏;安晉元;趙益民;朱滿座;;印制線拐角的頻域分析[J];西安交通大學學報;2007年12期

本文編號：1678441