本文選題：FLUENT + 橢圓螺旋管道混合器�。� 參考：《機械科學與技術》2017年05期

【摘要】：應用CFD技術研究了橢圓螺旋流道內兩相液體在充分發展條件下的混合效果。基于FLUENT軟件,對混合性能進行了數值模擬研究,討論了橢圓螺旋管道混合器的截面形狀、曲率半徑、螺距3種因素對該混合器混合效果的影響。模擬所得液相的流動狀態與實驗結果具有很好的一致性。提取相應截面液體的混合不均勻系數,分析結果表明:截面形狀的變化會給螺旋管道混合器造成不同程度的狹小區域,對混合均勻性影響較大;增加螺距會對混合產生消極的影響;當曲徑為某一特征值時,混合效果可達到最好狀態;同時,通過仿真分析得出,液體流速的改變對混合器中液體的混合效果影響不大;通過對流場內部剪切速率、流線、質點速度場的分析,討論了粒子無序運動是螺旋混合器內液體充分混合的關鍵因素。
[Abstract]:The mixing effect of two-phase liquid in the elliptical spiral channel was studied by CFD technique under the condition of full development. Based on FLUENT software, the mixing performance is numerically simulated, and the influence of three factors, such as section shape, curvature radius and pitch, on the mixing effect of the elliptical spiral pipe mixer is discussed. The flow state of the simulated liquid phase is in good agreement with the experimental results. The analysis results show that the change of cross section shape will cause a narrow area to different extent for the helical pipe mixer, which has a great influence on the mixing uniformity. Increasing pitch will have a negative effect on mixing, when the curved diameter is a certain eigenvalue, the mixing effect can reach the best state. At the same time, the simulation analysis shows that the change of liquid velocity has little effect on the mixing effect of liquid in mixer. Through the analysis of the shear rate, streamline and particle velocity field in the flow field, it is discussed that the disordered motion of particles is the key factor for the sufficient mixing of liquid in the helical mixer.
【作者單位】： 西安理工大學機械與精密儀器工程學院;
【分類號】：TQ027.1

【相似文獻】

相關期刊論文 前10條

1 顧紅芳,孫丹,章燕謀,陳聽寬;V型縱槽對水平螺旋管外冷凝傳熱的強化[J];化學工程;2000年05期

2 趙立新;華正榮;關鳳珠;蔣明虎;李楓;張勇;;螺旋管分離器流場分布及影響規律分析[J];化工機械;2010年05期

3 關九宇;;滾軋不銹鋼雙面螺旋管制造工藝[J];壓力容器;1985年06期

4 項紹偉;新型螺旋管傳熱經濟效益分析和應用[J];湖北化工;1986年01期

5 李朝陽;馬貴陽;朱本光;羅凱;王浩麗;;螺旋管內油水分離數值模擬[J];化學工程;2011年08期

6 鄭思義;;松散物料的柔性送料機構[J];機械制造;1990年08期

7 宋U，

本文編號：1796483