藍寶石拋光樹脂銅盤的制備及其性能研究
發布時間:2018-04-01 20:33
本文選題:聚酚氧 切入點:磨具 出處:《大連理工大學》2015年碩士論文
【摘要】:藍寶石材料已經成為目前各個領域的發展基礎。由于藍寶石具有優異的力學性能而被廣泛的應用,藍寶石所制成的器件的質量、壽命和發光效率在很大的程度上都依賴于其表面質量,所以目前藍寶石的加工重點就是如何能高效的獲得藍寶石表面質量。針對單晶藍寶石這種大批量生產的硬脆難加工的材料能獲得無損超光滑表面,本文提出了藍寶石拋光所用樹脂銅盤的制作方法。以銅粒子和樹脂基體組成樹脂銅盤,通過選用不同的樹脂作為基體,使其向高耐熱和高耐磨等方向發展。將銅粉和聚酚氧樹脂共混制備聚酚氧/銅復合材料,考察了銅含量和銅粒徑對復合材料的力學性能、熱變形溫度和摩擦磨損性能的影響。實驗結果表明:當銅粒徑為300#時,摩擦系數出現先增加后減小的趨勢。銅含量為70%時,其熱變形溫度達到最高89.7℃,復合材料的力學性能和耐磨性較好;隨著銅粒徑的增加,其力學性能出現減小的趨勢,其磨損率和摩擦系數隨著粒徑的增大逐漸減小。考慮綜合性能,選擇粒徑為300#作為復合材料的銅粒徑。以聚酚氧同甲階酚醛樹脂混合后作為樹脂基體,研究了聚酚氧/甲階酚醛比例、銅粒子含量對聚酚氧/甲階酚醛/銅復合材料力學性能及磨損性能的影響。結果顯示:當聚酚氧:甲階酚醛為6:4,銅含量為70%,粒徑300#時,復合材料的熱變形溫度達到最高,為115.7℃,同時具有最小的磨損率和摩擦系數,說明酚醛的最佳加入量為40%時,會使得復合材料的綜合性能得到提升。
[Abstract]:Sapphire materials have become the basis of development in various fields. Sapphire has been widely used because of its excellent mechanical properties, and the quality of devices made of sapphire. Both lifetime and luminous efficiency depend to a great extent on their surface quality, So at present, the focus of sapphire processing is how to obtain the surface quality of sapphire efficiently. In this paper, the preparation method of resin copper disk used in sapphire polishing is put forward. The resin copper disk is composed of copper particles and resin matrix, and different resins are selected as the matrix. The polyphenoxy / copper composites were prepared by blending copper powder with polyphenoxy resin. The mechanical properties of the composites were investigated by copper content and copper particle size. The experimental results show that the friction coefficient increases first and then decreases when the copper particle size is 300#. When the copper content is 70, the thermal deformation temperature reaches the highest 89.7 鈩,
本文編號:1697215
本文鏈接:http://sikaile.net/kejilunwen/huagong/1697215.html
最近更新
教材專著