發布時間：2019-02-14 07:24

【摘要】：針對傳統m推演型濾波器插入損耗大、帶內平坦度不理想等問題,提出了一種改進型帶通濾波器設計優化方法。本文首先介紹了濾波器各子級的設計方法,利用ADS對濾波器參數進行迭代優化設計,并采用PCB工藝制備了帶通濾波器樣品同時進行了傳輸特性的測量,最后將其實際應用于泄漏電纜周界入侵檢測系統中提高了硬件前端的信噪比。測量結果表明,在25.75~36.25 MHz的通帶范圍內,插入損耗小于1.5 d B,帶內平坦度優于0.5d B,反射系數小于-15 d B,過渡帶性能理想;在陷波點20 MHz、45 MHz處衰減大于-50 d B。在本文的最后,對周界入侵檢測系統漏報率、誤報率、正確率進行了初步測試,結果表明虛警率從每小時1次減少至2天內未發生報警,該濾波器結構有效地解決了系統虛警率高的問題,提高了系統的穩定性。
[Abstract]:Aiming at the problems of large insertion loss and unsatisfactory in-band flatness of the traditional m-derived filter, an improved design optimization method of bandpass filter is proposed. In this paper, the design method of each sub-level of filter is introduced, the parameters of filter are optimized iteratively by ADS, and the sample of bandpass filter is prepared by PCB process, and the transmission characteristic is measured at the same time. Finally, it is applied to the leakage cable perimeter intrusion detection system to improve the signal-to-noise ratio of the hardware front end. The results show that the insertion loss is less than 1.5 dB, the in-band flatness is better than 0.5 dB, and the reflection coefficient is less than -15 dB in the range of 25.75 ~ 36.25 MHz. At the notch point of 20 MHz,45 MHz, the attenuation is greater than -50 dB. At the end of this paper, the false alarm rate, false alarm rate and false alarm rate are reduced from once an hour to 2 days. The filter structure can effectively solve the problem of high false alarm rate and improve the stability of the system.
【作者單位】： 寧波大學信息科學與工程學院;
【基金】：國家自然科學基金(61571251,61501272) 浙江省公益技術應用研究項目(2015C34004) 寧波市自然科學基金(2016A610064)
【分類號】：TN713

【相似文獻】

相關期刊論文 前1條

1 李晶皎;許哲萬;王愛俠;陳勇;;高速包分類平臺的FPGA設計[J];東北大學學報(自然科學版);2012年08期

，

本文編號：2421970