【摘要】：隨著大規模集成電路、高頻開關元件以及無線通訊模塊在電子設備中的廣泛使用,大量電子輻射噪聲隨之產生,并以空間電磁場的形式向外傳播,不僅影響設備自身的正常工作,而且還會通過電磁場輻射的形式干擾外部設備的工作。目前的電磁兼容問題分析方法大多是從理論和建模方面分析輻射問題,并不能對噪聲源特征進行判定和診斷,且由于模型的理想化,導致了結果與實際有著一定的誤差,因此復雜電子設備電磁輻射噪聲源的識別和診斷成為了電磁兼容輻射分析中的一大挑戰。針對上述問題,本文研究了“基于NLPCA和JADE算法的EMI輻射源噪聲診斷方法研究”,具體包含以下內容:(1)從天線輻射理論出發,通過對復雜電子設備輻射機理的分析,針對實際電路中輻射線纜長度為電大尺寸時信號傳播存在時延以及線路阻抗失配時電路存在反向行波這兩種情況建立了適用性廣泛的輻射卷積噪聲模型。(2)研究復雜電子設備多輻射源的定位方法。利用NLPCA和JADE算法分別從信號的時域和頻域角度對多輻射源輻射噪聲進行分析,獲得若干個獨立的噪聲信號,作為輻射噪聲超標源頭的備選信號。利用功率譜對分離后的獨立輻射電磁干擾噪聲信號進行分析,提取出各信號的頻率特征,通過與PCB板的疑似輻射源進行比對,從而診斷出引起輻射超標的主要原因。(3)進行三組驗證性實驗,通過對雙共模模型、雙差模模型和共差�；旌夏Ｐ偷脑肼曅盘�(hào)盲分離,并對分離后的獨立信號進行能量頻譜分析,找出輻射超標的原因,驗證了該定位方法的可行性。最后通過兩個實際的復雜電子產品進行案例分析,驗證了該方法實際應用的有效性,成功找出了輻射超標的原因,并根據超標原因采取對應的整改,使電子設備通過國標測試。通過理論的分析研究和實驗結果的驗證,本文提出的定位方法對復雜電子設備的電磁兼容多輻射源信號分離研究有著重要的借鑒價值,而且對電磁兼容的整改工作有著積極的指導意義。
[Abstract]:With the widespread use of large scale integrated circuits, high-frequency switching elements and wireless communication modules in electronic devices, a large amount of electronic radiation noise is generated and propagates outward in the form of space electromagnetic fields. It not only affects the normal operation of the equipment itself, but also interferes with the work of the external equipment through electromagnetic radiation. At present, most of the analysis methods of EMC are based on theory and modeling, which can not judge and diagnose the characteristics of noise source, and because of the idealization of the model, there is a certain error between the results and the reality. Therefore, the identification and diagnosis of electromagnetic radiation noise sources in complex electronic equipment has become a major challenge in EMC radiation analysis. In order to solve the above problems, this paper studies the method of noise diagnosis of EMI radiation source based on NLPCA and JADE algorithm, which includes the following contents: (1) based on the antenna radiation theory, the radiation mechanism of complex electronic equipment is analyzed. In this paper, a widely applicable radiation convolution noise model is established for the real circuit in which the signal propagation delay exists when the length of the radiation cable is electrically large and the circuit has reverse traveling wave when the line impedance mismatches. (2) the complex convolution noise model is studied. Location method of multiple radiation sources for miscellaneous electronic equipment. NLPCA and JADE algorithms are used to analyze the radiated noise of multiple radiation sources in the time domain and frequency domain respectively, and several independent noise signals are obtained, which are used as alternative signals for the radiation noise to exceed the standard source. The independent radiated electromagnetic interference (EMI) noise signal after separation is analyzed by power spectrum, and the frequency characteristics of each signal are extracted, and compared with the suspected radiation source of the PCB board. Thus, the main causes of radiation exceeding the standard are diagnosed. (3) three groups of confirmatory experiments are carried out. The noise signals of the two common mode models, the double differential modes model and the common-difference mode mixed model are separated blindly, and the energy spectrum of the separated independent signals is analyzed. The reason of radiation exceeding the standard is found, and the feasibility of this method is verified. Finally, through the case analysis of two real complex electronic products, the validity of the method is verified, the reason of radiation exceeding the standard is found out successfully, and the corresponding rectification is taken according to the reason of exceeding the standard, so that the electronic equipment can pass the national standard test. Based on the theoretical analysis and experimental results, the localization method proposed in this paper has important reference value for the study of EMC multi-emitter signal separation in complex electronic equipment. Moreover, it has positive guiding significance to the rectification and reform of EMC.
【學位授予單位】：南京師范大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TN03

【參考文獻】

相關期刊論文 前10條

1 陳慶彬;陳為;;開關電源中變壓器共模傳導噪聲抑制能力的評估方法[J];中國電機工程學報;2012年18期

2 王世山;朱葉;崔永生;;基于“負參數”理論的EMI濾波器寄生參數的雙重消除[J];電工技術學報;2011年10期

3 趙陽;顏偉;邱曉暉;;電力載波通訊中輻射噪聲的分析與抑制[J];中國礦業大學學報;2011年01期

4 趙陽;顏偉;趙波;羅永超;李世錦;;電路輻射干擾機理診斷與特性估計[J];電工技術學報;2010年10期

5 趙陽;董穎華;陸ZK泉;姜寧秋;顏偉;;EMI噪聲分離網絡在電力線噪聲分析中的應用[J];中國電機工程學報;2010年21期

6 趙陽;羅永超;顏偉;趙波;李世錦;陸ZK泉;邱曉暉;;高頻電路輻射干擾快速分析與預估方法[J];電波科學學報;2010年03期

7 任小永;姚凱;曠建軍;阮新波;;損耗最小化輸出濾波電感的設計[J];中國電機工程學報;2008年27期

8 孟進;馬偉明;張磊;潘啟軍;趙治華;;帶整流橋輸入級的開關電源差模干擾特性[J];電工技術學報;2006年08期

9 陳文潔;楊旭;王兆安;;集成模塊用有源電磁干擾濾波器的設計[J];中國電機工程學報;2005年24期

10 和軍平,陳為,姜建國;開關電源共模傳導干擾模型的研究[J];中國電機工程學報;2005年08期

相關碩士學位論文 前2條

1 夏歡;基于ICA和STFFT算法的輻射EMI噪聲分析與診斷方法[D];南京師范大學;2015年

2 平云娟;基于盲源分離的輻射EMI噪聲分析與診斷方法研究[D];南京郵電大學;2011年

，

本文編號：2237768