【摘要】：為實現在高亮度條件下模型外形輪廓的測量,首先在計算機上生成隨機矢量化散斑圖案,并用激光雕刻技術制成散斑片作為散斑投射模板,采用光波為850 nm的VCSEL激光器作為投射光源并制成激光散斑投射器。在高亮度條件下,通過給相機加裝窄帶濾光鏡實現散斑圖像的清晰獲取,最后基于數字圖像相關法完成圖像的立體匹配并最終解算出模型點云。實驗表明:該方法在20 400 lx條件下仍然可以實現模型的外形輪廓測量,且標準球測量結果相對偏差為0.038 4%;應用近紅外激光散斑投射并給相機加裝窄帶濾光鏡可有效減少干擾光影響,可以在高亮度條件下完成模型輪廓的精準測量。
[Abstract]:In order to measure the contour of the model at high luminance, the random vectorized speckle pattern is generated on the computer, and the speckle slice is made by laser engraving as the speckle projection template. A laser speckle projector is fabricated by using a VCSEL laser with a wavelength of 850 nm as a light source. Under the condition of high brightness, the speckle image can be obtained clearly by adding a narrow band filter to the camera. Finally, the stereo matching of the image is completed based on the digital image correlation method and the model point cloud is finally solved. The experimental results show that the method can still be used to measure the contour of the model under the condition of 20 400 LX. The relative deviation of the standard sphere measurement results is 0.038. Using near-infrared laser speckle projection and adding narrow-band filter to the camera can effectively reduce the influence of interference light and complete the accurate measurement of the model profile under the condition of high brightness.
【作者單位】： 西安交通大學機械工程學院機械制造系統工程國家重點實驗室;
【基金】：國家自然科學基金資助項目(51675404,51421004)
【分類號】：TN24;TP391.41

【相似文獻】

相關期刊論文 前10條

1 戴蓉;激光輪廓測量技術在無損檢測中的應用[J];無損檢測;2000年09期

2 司書春,王蘊珊,徐建強;移相式輪廓測量法相移誤差的計算機模擬校正[J];光電子·激光;2001年08期

3 田青;王輝;任志君;;數字全息再現像的激光散斑消除的研究[J];應用激光;2006年06期

4 姚q;明海;;激光散斑驗光[J];激光與紅外;1983年04期

5 王茗yN;曾亞光;楊國建;;基于散斑強度漲落調制的微循環激光散斑成像[J];量子電子學報;2014年01期

6 潘志方,王仕t，

本文編號：2135493