本文選題：紅外光學 + 光學系統設計　； 參考：《西安工業大學》2015年碩士論文

【摘要】：紅外搜跟場景投射器可以在實驗室環境中模擬動態點源紅外目標,為紅外搜索跟蹤系統的各項技術指標的評測提供人為可控,低成本,可反復測試的實驗條件,在紅外搜索跟蹤設備的設計研發過程中,對系統的性能進行綜合評價。投影子系統的光學系統是紅外搜跟場景投射器的重要組成部分,本課題根據紅外搜跟場景投射器的總體技術指標,利用ZEMAX光學設計軟件,設計了一基于黑體輻射的紅外雙通道準直投射系統。系統采用一個無焦系統和后聚焦系統的組合系統,工作波波段為8～12μm,系統焦距為230.56mm,視場為12。,出瞳距為600mm,出瞳直徑為100mm,各視場的MTF曲線在201p/mm處均接近衍射極限,各視場彌散角均小0.2mrad,畸變小于2%,像質優良。同時為了滿足儀器使用要求,引入衍射元件對系統進行了光學被動式消熱處理,系統各項指標滿足要求。最后為了確保加工,對系統進行了公差分析,在給定的公差范圍內,經過蒙特卡洛模擬分析,光學系統的各項指標均滿足總體要求。
[Abstract]:The infrared tracking scene projector can simulate the dynamic point source infrared target in the laboratory environment, and provide the experimental conditions for the evaluation of the various technical specifications of the infrared search and tracking system that can be artificially controllable, low-cost, and can be repeatedly tested. In the process of design and development of infrared search and tracking equipment, the performance of the system is evaluated synthetically. The optical system of shadow casting system is an important part of the infrared tracking scene projector. According to the overall technical specifications of the infrared tracking scene projector, this paper uses the ZEMAX optical design software. An infrared double channel collimation projection system based on blackbody radiation is designed. The system is composed of a non-coke system and a rear focusing system. The working wave band is 80.12 渭 m, the system focal length is 230.56mm, the field of view is 12.The pupil distance is 600mm, and the pupil diameter is 100mm. The MTF curves of each field of view are close to the diffraction limit at 201p/mm. The dispersion angle of each field is 0.2mrad. the distortion is less than 2 and the image quality is good. At the same time, in order to meet the requirements of the instrument, the diffractive elements are introduced to the system for optical passive heat treatment, and the system indexes meet the requirements. Finally, in order to ensure the machining, the tolerance analysis of the system is carried out. In the given tolerance range, through Monte Carlo simulation analysis, each index of the optical system meets the overall requirements.
【學位授予單位】：西安工業大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TN216

【參考文獻】

相關期刊論文 前3條

1 劉雨沁;張孟偉;;變倍光學系統的公差分析[J];光學儀器;2013年02期

2 鄭雅衛,高教波,王軍,陳慧玲;動態紅外場景準直投射光學系統的設計[J];激光與紅外;2005年08期

3 于洋;蹇毅;潘兆鑫;金亞平;湯心溢;;紅外二次成像無熱化光學系統設計與實測[J];紅外與激光工程;2013年12期

，

本文編號：1952075