本文選題：自動檢測 + 硬質合金棒材缺陷��； 參考：《傳感技術學報》2016年05期

【摘要】：PCB板鉆頭是由超細硬質合金棒材加工出來的,而超細硬質合金棒材在無心磨削加工過程中常會產生崩角、磨面等缺陷。針對目前硬質合金棒材缺陷人工檢測效率低、誤檢率高的問題,采用電渦流無損檢測方法,開發了一套硬質合金棒材缺陷檢測系統,以單片機為控制核心,設計了數據采集、A/D轉換、通訊、執行機構等電路,開發了相應的控制軟件。通過實驗研究了檢測系統的提離效應和邊界效應,實驗結果表明研發的硬質合金棒材缺陷檢測系統能有效分選出有缺陷的棒材,可以有效提高檢測準確率和檢測效率。
[Abstract]:The PCB plate bit is manufactured from the ultra-fine cemented carbide bar, and the defects such as caving angle and grinding surface are often produced in the centerless grinding process of the ultra-fine cemented carbide bar. Aiming at the problems of low efficiency and high error detection rate of carbide bar defects at present, a set of defect detection system of cemented carbide bar is developed by using eddy current nondestructive testing method, with single chip microcomputer as the control core. The A / D conversion, communication and actuator circuits of data acquisition system are designed, and the corresponding control software is developed. The lifting effect and the boundary effect of the testing system are studied experimentally. The experimental results show that the developed system can effectively separate out the defective bars, and can effectively improve the detection accuracy and efficiency.
【作者單位】： 湖南大學國家高效磨削工程技術研究中心;硬質合金國家重點實驗室;
【基金】：湖南省自然科學基金項目(12JJ6037) 硬質合金國家重點實驗室項目(201103003)
【分類號】：TN41;TP274

【相似文獻】

相關重要報紙文章 前1條

1 田都順;陜硬公司又一產品填補國內空白[N];中國航空?qǐng)?bào);2000年

相關碩士學位論文 前2條

1 張衛豐;超細硬質合金棒材的制備研究[D];武漢理工大學;2004年

2 李典紅;硬質合金棒材缺陷電渦流檢測系統開發[D];湖南大學;2013年

，

本文編號：1884501