發布時間：2018-05-14 08:12

  本文選題：離心泵 + 斷軸��； 參考：《水泵技術》2017年05期

【摘要】：2016年末至2017年初,我公司對一臺其他廠家生產的電廠用多級鍋爐給水泵進行了檢修。該泵主要故障為運行500小時后出現了斷軸的問題,現場檢修并更換主軸后振動仍然較大,運行不平穩。將該給水泵解體后發現密封環間隙超標,平衡盤、平衡座磨損嚴重,最主要的問題是現場新?lián)Q的主軸已經彎曲變形。經研究決定重新測量檢查、更換主軸,各葉輪密封環處加工成統一外徑,重新加工配制密封環,在不更換葉輪的情況下實施有效的修復。對平衡盤、平衡座重新測繪加工處理,該給水泵經過處理修復后,運行狀況良好,達到了預期效果。
[Abstract]:From the end of 2016 to the beginning of 2017, our company overhauled a multistage boiler feedwater pump in a power plant made by other manufacturers. The main failure of the pump is the failure of the shaft after 500 hours of operation. The vibration is still large and the operation is not stable after the maintenance and replacement of the main shaft. After disintegrating the feed pump, it is found that the clearance of the seal ring exceeds the standard, and the balance disc and the balance seat are worn seriously. The main problem is that the newly changed spindle has been bent and deformed. After study, it is decided to re-measure and check, to replace the spindle, to process each impeller seal ring into uniform outer diameter, to reprocess and prepare the seal ring, and to carry out effective repair without replacing impeller. After the reprocessing of the balance plate and the balance seat, the feed pump is in good operation condition and the expected effect is achieved.
【作者單位】： 沈陽市工業泵廠(有限公司);
【分類號】：TM621.2

【相似文獻】

相關期刊論文 前4條

1 屈云亮;電機斷軸再接[J];中小型電機;1998年03期

2 盧健翔;改進平衡盤以消除高壓給水泵的故障[J];電力技術通訊;1975年04期

3 尹福偉;;DG100—59型給水泵平衡盤裝置的改進[J];黑龍江電力技術;1986年04期

4 馮金泉;;DG270-140給水泵平衡盤事故原因分析[J];華東電力;1982年04期

，

本文編號：1887067